How to remove dried film from plastic windows. How to remove stuck film from windows How to easily remove film from plastic windows

Today there are several types of film, each of which is intended for reliable protection homes from the scorching rays of the sun. At correct use This material allows you to reduce the summer temperature in the rooms by five to ten degrees.

This protective agent has only one serious drawback - the difficulty of removing it from windows. Each film contains an adhesive substance with which it is fixed to the glass. And in many cases, when removed, it can leave visible marks on the window, which will negatively affect its appearance.

Sun protection film on the window

All existing species films are made from materials that reflect light, and many of them contain aluminum, which can also leave unsightly spots on glass. It is quite difficult to remove them without causing any harm to the glass surface. But if you use a number of chemicals designed to clean complex stains, you can try to remove traces of the use of protective film with minimal damage to the glass.

All modern materials, which are designed to protect rooms from excessively high temperatures, contain aluminum and other substances that make them so difficult to remove from surfaces. In order not to leave unsightly streaks and noticeable stains on the glass, the removal of such protective agents should be approached as carefully and responsibly as possible. There are several most common ways to be careful, each of which can lead to success.

Steaming

If you peel off the sun protection material from windows without preliminary preparation, then the likelihood of stains and noticeable traces from the adhesive is enormous.

The ideal way to prepare the film for removal is to use a modern steamer.

The procedure for cleaning windows from material using a steamer is carried out in several stages:

1. A small area is heated using hot steam from a steamer. It is very important that the steam is directed to a specific place on the window.
2. About five minutes after steam treatment, you should pick up a piece of film and gently pull it towards you, separating it from the window.
3. The new section of the window is heated again until the material begins to move away from the glass.

The film area is heated using a steamer
After five minutes it separates from the window

This is the most gentle and simple way to remove sun protection film. In this case, the window remains minimum quantity traces that can be easily removed with a simple soap solution. This is just one of the simple answers to the question of how to remove film from window glass without visible marks.

Detergents and cleaning products

From others effective ways we can highlight the use of powerful ones designed for cleaning glass surfaces. They allow you to remove stains and film marks from windows without special effort, but when using them, safety precautions must be observed, which consists of the following rules:

• When treating surfaces with chemicals, it is necessary to use the provided protective equipment. These include gloves, closed clothing and a respirator;
• compliance with the dosage specified by the manufacturer on the detergent container;
• compliance with the manufacturer's recommendations to avoid contact of the substance with certain materials that are sensitive to the components of the cleaning product.

Use protective equipment
Study the dosage

You can clean windows using these effective means, How:

• Domax. This substance is intended for gentle care of glass ceramics and does not contain abrasive substances;
• Cosmofen;
• Schumann;
• Fenosol.

Schumanite is an effective remedy

However, even modern powerful preparations designed for cleaning surfaces cannot always cope with the consequences of the protective film material remaining on the window glass. In this case, stains and other marks will have to be removed using a more rigid scraper, which is designed for cleaning glass ceramics. The remaining traces are then removed using a modern Fenosol cleaner. After this, the glass is washed first with a soap solution and then with warm, clean water.

All the methods described above, which tell you how to remove sun protection film from glass, are also suitable for cleaning wooden windows and for modern PVC and metal-plastic profiles. Compliance with safety precautions and the dosage of cleaning products will allow you to rid your windows of residues protective material without any particular harm to the glass and without harm to health.

Scraper for cleaning glass ceramics

Other ways

There are other ways you can try to remove film from your window. One of them is to use a utility knife or other sharp object, such as scissors. During the procedure, you need to carefully pry the edge of the film with a knife to separate it from the glass, and then pull it towards you. It is recommended to roll up the already peeled off areas into a tube so that they do not stick to the window again.

You can also remove some types of film using newspapers and soapy water. The procedure is carried out in several stages:

1. Regular newspapers are placed over the entire glass area.
2. The newspapers are sprayed with soapy water until they begin to stick to the surface.
3. Leave for an hour, regularly wetting the paper.
4. Remove newspapers and film, which will come off much easier after the procedure.

Newspapers are placed on the entire glass
They are sprayed with soapy water
Leave for an hour, constantly moistening
Easily remove newspapers and film

Precautions when removing film stains from glass

When carrying out work to clean windows from traces of solar control film, you should follow the recommended precautions. Some chemical cleaners may have negative impact on human skin and respiratory tract, and using sharp objects can cause injury. Therefore, when removing film stains, you must adhere to the following rules:

• carry out all work related to chemical cleaning substances only with strong, impermeable gloves;
• when wiping off marks, do not press hard on the glass, as this may damage its integrity;
• when working with sharp objects (knife, scissors, scraper), you should act as carefully as possible so as not to get hurt or damage the window;
• avoid getting hit chemicals on unprotected skin, eyes or respiratory tract;
• Keep materials and tools intended for removing marks from glass surfaces out of the reach of children.

Caring about warmth and comfort in their homes, many people prefer installing plastic windows. These modern designs distinguished by impeccable appearance, sealed. Usually, after installation is completed, a protective film remains on the frames, which is often forgotten to remove in time. Over time, it firmly dries to the plastic surface, after which it becomes difficult to get rid of. It happens that you need to remove the sun from the windows protective film or remove traces of glue. Effective methods will help you cope with these tasks.

Why it can be difficult to remove protective film from windows

The main function of the film applied to plastic window frames in the factory is to provide effective protection products during transportation. But under the influence of an aggressive external environment (heat, ultraviolet radiation), they are capable of sticking to a plastic surface. In addition, when making protective films, high-quality adhesive is not always used, which makes it even more difficult to remove such protection over time. You can get rid of the film without making much effort within 10 days after installing double-glazed windows. If for some reason it was not possible to do this on time, do not despair.

If the protective film is not removed in time, over time it will be much more difficult to do so.

How to remove film and adhesive tape from plastic windows

Using chemical or mechanical methods, you will be able to cope with this task. To work you will need:

• construction or household hair dryer;
• scraper for cleaning glass-ceramic surfaces;
• denatured alcohol;
• eraser;
• acrylic solvent;
• White spirit;

When choosing a store-bought product, you must carefully study its composition. Solvents containing harsh acids and acetone can damage frames, as can abrasive cleaning compounds.

Mechanical methods

A scraper, eraser, hair dryer and other tools will help remove the film mechanically.

How to use a scraper

The method does not require any special physical effort, since the film can be removed very easily using a scraper. However, careless handling of the tool may damage the plastic frames.

1. Using a scraper designed specifically for glass-ceramic panels, carefully remove any remaining film.
2. After the procedure, clean the surfaces with Cosmofen 10, Fenosol or acrylic solvent R-12.

How to remove film using an eraser

To remove film from window frames You can use an ordinary soft eraser. Although the method requires a lot of physical effort, using it you will not cause damage to the surfaces. Using an eraser, you can also get rid of sun protection film on windows.

1. Rub the film remaining on the surface of the frames or glass with an eraser.
2. Remove any remaining adhesive using white spirit or any other cleaner.

Using a hair dryer or steam generator

This method is different high efficiency and allows you to get rid of the film quickly and easily. However, you should work with such devices with the utmost caution: excessive overheating of the PVC surface can cause irreparable harm to it. If you have an industrial hair dryer at hand, the procedure for removing old protective film will not take much time and effort. If you don’t have one, you can get by with an ordinary household appliance or a steam generator.

1. Heat the surface of the film.
2. Carefully pry off its edge with a knife or other sharp object.
3. Remove any remaining glue using the same cleaners.

Using a hair dryer, remove protective film from windows

Chemical methods

Using tools and devices for removing protective film from plastic window frames, even a specialized scraper, can scratch the PVC profile. It is for this reason that for many people faced with solving such a problem, the most acceptable option is the use of chemicals. With their help, you can remove the film with a minimum of effort and without damaging the surface of the window. However, you should work with such substances carefully.

Denatured alcohol for film removal

One of the means that allows you to quickly and efficiently clean plastic surfaces from protective film is denatured alcohol. When using it, personal safety precautions should be observed, protecting open areas skin and mucous membranes. The method is simple and effective and does not require any special physical effort.

1. Pour the substance into a spray bottle.
2. Apply denatured alcohol to the surface to be treated.
3. After 5 minutes, remove the film by prying it off with a sharp object or a stationery knife.

How to remove film using Schumanite

The effective substance is detergent Schumann. Using it, you do not have to make any special physical effort when removing protective coatings from the window. Since the components of Schumanite are very aggressive, remember safety precautions: use gloves and safety glasses, and ventilate the room well.

1. Apply it to the surface.
2. Remove the film without the need for special physical effort.

Step-by-step instructions for using RP-6

The RP-6 paint remover will also help you get rid of the protective film. Its effectiveness is quite high, and working with it requires having protection on your hands.

1. Apply a generous layer of the substance to the surface of the film. After 10 minutes, the film will begin to foam right before your eyes.
2. Remove the coating. It will come off without much effort.
3. Wash off any remaining adhesive with soapy water.

How to use Scotch Remover to remove adhesive tape and film from PVC windows

A specialized product designed to remove complex stains from glass and plastic surfaces, known as Scotch Remover, will also provide the required effect when removing film. When working with it, you must use protective glasses and gloves, and also ventilate the room well.

1. Shake the container with the product.
2. Spray the substance onto the film surface.
3. Remove the film.
4. Wipe the surface cleaned from it with a clean rag.

How to use penetrating lubricant VD-40

One of the most gentle products for plastic surfaces is VD-40. This lubricant is widely used in the automotive industry. The composition includes a number of components that can penetrate the most complex contaminants. With its help, you can easily get rid of protective films stuck to double-glazed windows, as well as clean adhesive traces. It is recommended to use gloves when working.

1. Apply the composition to the film.
2. After a few minutes, remove it from the surface.
3. Wipe the area to be treated with soapy water and wash with clean water.

VD-40 is a universal cleaner that will easily remove film from PVC window frames and adhesive traces

Attention! When working with chemicals, you must remember personal safety, trying to avoid contact of these products with exposed skin and mucous membranes. To do this, use safety glasses and rubber gloves.

Methods for removing solar control film (foil) from a window

During hot summer days, the windows and glazed balconies of many apartments are exposed to scorching sunlight, which negatively affects the internal microclimate of the premises. A fairly effective means of protection against them is a film that can reflect sun rays.

With the onset of autumn and cold weather, the need for such protection disappears and the film must be removed. However, such materials can become firmly embedded in the surface of the window under the influence of the sun, after which it becomes difficult to remove them. To solve the problem you can use:

• denatured alcohol;
• steam generator;
• eraser.

You can also remove the sun protection film using various detergents:

• Domax;
• Schumann;

When using these formulations, it is also advisable not to forget about safety precautions and follow the manufacturers’ recommendations and dosages. If after them the adhesive base of the film remains, you can use the following means:

• Kiehl Tablefit spray liquid: apply to a cloth and clean the surface;
• stain remover Taygeta S-405: apply to remaining glue for 15–30 seconds;
• FORMULA X-5 liquid solution: effective in 10–15 minutes;
• Super CMF-240 from the Krizal company: positioned as a “dirt separator”, it removes the adhesive base of the film worse than the previous ones, but for allergy sufferers it may be the only applicable product from industrial compositions;
• highly alkaline liquid Merida Impet for removing stubborn stains: apply to the glue for 2 minutes.

Products for removing adhesive stains from various surfaces - gallery

Domax will allow you to get rid of film and its traces
Cosmofen is a strong and highly toxic cleaner that is highly effective Fenosol is a high quality cleaner used on plastic surfaces
Kiehl Tablefit is a product designed to remove glue traces
FORMULA X-5 will quickly remove traces of glue Super CMF-240 high-quality universal cleaner

Soap solution and old newspapers

There is another method of removing sun protection film that does not require any special material costs. To use it you will need:

• soap solution;
• old newspapers.

Operating procedure:

1. Holding the newspaper with your hand, lean it against the glass and moisten it generously with soapy water using a sprayer. Repeating this operation again and again, it is necessary to cover the entire window space with newspapers.
2. Leave newspapers stuck to the window for 1 hour, periodically spraying them with soapy water.
3. Remove the sun protection film along with newspapers.

This one is simple and effective method very effective, but requires a fair amount of time. Using it, you will not harm the surfaces being treated.

Safety precautions

1. When removing protective films from double-glazed windows, it should be taken into account that many of the chemicals are very aggressive solutions and can cause harm to the body. For this reason, they should be handled carefully, remembering to use rubber gloves, safety glasses, and, if you are prone to allergic reactions, a respirator.
2. When wiping off adhesive from glass, do not press too hard on the surface. Otherwise, the glass may crack or fly out.
3. When working with sharp objects, you must be careful not to damage plastic surfaces or accidentally injure yourself.

Using simple mechanical and by chemical means removing protective film coating from windows, you can achieve desired result without making much effort. However, it should be remembered that such work cannot be rushed, and when performing it, one should not forget about safety precautions.

Many users, faced with the problem of window film firmly “fused” to the PVC profile, rush to experiment, which does not always end well. Especially in the case of colored windows, there is a risk of destroying them. The OKNA MEDIA portal will tell you how to effectively and without disastrous consequences remove old protective film from plastic windows.

All plastic windows come to the market with frames protected by the manufacturer using self-adhesive film. According to the rules, the protective film must be removed as soon as possible after completing the window installation - especially when the PVC window is exposed to direct sunlight.

Why is it so difficult to remove old protective film from PVC windows?

Unfortunately, this happens quite often, and due to the negligence of installers or the user himself, the protective film on the PVC profile can remain even for several years. In this case, when the hands get around to putting the new plastic windows in order, the user will be in for an unpleasant surprise - it is almost impossible to remove the protective coating.

It is difficult to remove old window film from a plastic window profile because it consists of two layers. The outer layer (transparent film) begins to peel off under the influence of ultraviolet rays and is relatively easy to clean. But at the bottom there is a second layer of white plastic with markings applied - it is this that sticks so strongly to the substrate.

Availability is especially bad old film looks like a tree-like profile because usually a protective coating is used white. Under the influence of UV rays, the film undergoes vulcanization and adheres very firmly to the surface of the PVC window. At the same time, it becomes less durable and breaks easily.

Some people try to wash off the protective layer with gasoline, acetone or other solvents - this helps a little, but at the same time you can remove the wood texture that is used to laminate the frame (white PVC windows, of course, are insured against this). Experts do not recommend exposing the surface of colored PVC profile too strong mechanical impact(scraping or sanding) because it is very easy to damage the lamination layer.

Eureka: There is a way to get rid of old protective film!

Fortunately, there are several ways to get rid of the protective film, we suggest considering one of them. This method is simple, effective and, most importantly, will not destroy the plastic window. However, the procedure will take quite a long time and will require the use of a device with a steam cleaning function.

Such a device can be bought without problems; they are often sold in supermarkets. Please note that the package includes a special hose that allows you to fix the nozzle. Versions of this device often appear on sale, in which steam exits directly from the tank through a nozzle. In this case, you will have to constantly hold the heater in your hands during cleaning, but it will soon become clear that heating the film in the lower part of the frame is impossible in this case (the window sill gets in the way).

Work begins by filling the purifier with water and connecting to the power supply. After a few minutes, you can begin heating a small area of ​​the protective film with a jet of steam (hold the nozzle directly above the film or even touch it). Heat a small section of 1-2 cm across the entire width. If window film It's already too old and won't peel off, you'll have to reheat it (after cooling). At this time, you can heat the protective coating of the window from the other end.

To remove the protective film using steam, shortly after heating a small area, you should try to separate the film from the backing with your fingernail. This must be done carefully and slowly, across the entire width of the tape. This is the most important point. It is necessary to ensure that a small piece of the film peels off across its entire width. Then you can grab the end and slowly (!) tear off the film while simultaneously heating with steam from above and below (at the points of contact with the substrate).

If the protective film begins to tear and its fragment does not come off, you need to use a fingernail in this place and lead to a situation where it peels off again across its entire width. After removing a sufficiently long fragment, cut it off with scissors, leaving 2-3 cm so that there is something to cling to to continue further cleaning of the PVC profile.

After removing the protective layer, it remains on the surface of the window frame. white coating, which is quite difficult to wash off. And here there is a proven method - you can use a glass cleaner for this purpose (for example, Mister Muscle).

When buying new plastic windows, do not ignore the advice of the window company, which is clearly stated in the operating instructions, when it is worth removing the protective film from the PVC profile. This will allow you to save time and money, and save your nerves. In general, following the manufacturer’s recommendations not only in this point, but also in all others, is the key to the impeccable appearance and durability of your plastic windows.

After purchasing an apartment, the new owners are so busy putting things in order that they completely forget about the little things. The same thing happens after installing plastic windows, the frame and glass of which are covered with a protective film. After a certain period of time, under the influence of direct ultraviolet rays, the coating begins to crack, distorting the penetration of light. Plastic parts fade unevenly, and the glue eats into the surface structure quite firmly. To fix problems, you need to remove the protective film as quickly as possible.

Technology for removing film from plastic windows

According to manufacturers, the protective film must be removed within 10-12 days after installing plastic windows. This period is determined by the fact that the coating consists of two layers, which are attached to the frame with an adhesive base.

The inner part is quite delicate, for this reason it quickly collapses and begins to stick to plastic parts. The situation becomes more complicated with each passing day, forcing housewives to clutch their heads.

In the case of the top layer, there should be no problems; it comes off even after 2.5-4 months after installing the windows.

To clean the glass and frame from glue and remove the film without harm to the product, it is important to follow the specifics of the procedure. We will highlight effective methods and provide practical recommendations.

Method number 1. Construction hair dryer

To remove film from the surface of windows, you can use a hair dryer. Purchase the device in a specialized store or large hypermarket (Leroy Merlin, OBI, etc.). To carry out the procedure, it is not necessary to choose a product with several heating functions; it is enough to buy cheap option"for one time."

Read the instructions, plug the hair dryer into a socket, and heat it up. Never expose your hand to the air flow to avoid getting burned. Point the hairdryer not at the glass, but at the plastic frame. Maintain a distance of about 35-45 cm so that the film does not melt.

Under the influence high temperatures the adhesive base will soften, which will allow you to easily remove it from the surface of the windows. Pry up the free edge, walk over the surface with the terminals with a hard rag soaked in acetone or car enamel solvent.

Method number 2. Scraper

A kitchen scraper, which is used to clean enameled and glass-ceramic stoves, will help remove film from the surface of plastic windows. The tool is sold in “Everything for the Home” stores; it is a spatula with or without a rubber tip.

To use the tool correctly, use it to pry the free edge of the film, pull it slowly and at the same time help yourself with the scraper. Move along the inner (adhesive) part of the film, avoid breaking the protective material.

When the procedure comes to an end, inspect the glass and frame for the presence of glue. If the result is positive, spray the window cleaner over the entire surface, leave for a quarter of an hour, constantly renewing the composition. When the glue dissolves, remove it with a scraper.

Method number 3. Stationery eraser

This option is rightfully considered ineffective if the film is left on the windows for a long time (about 2-3 months). To remove the adhesive, purchase some school erasers. The main thing is that they are clean (without traces of a ballpoint pen or pencil).

Before starting the procedure, make sure that the surface to be cleaned is perfectly dry. Next, start rubbing the remaining glue with an eraser, rolling them into oblong lines. Proceed step by step, treat individual zones one by one (about 5-10 sq. cm.).

To increase efficiency, you can spray the frame and glass with a solvent for paints or car enamels; nail polish remover or pure acetone is also suitable.

Method number 4. "White spirit"

An excellent option for removing protective film from plastic windows is a hair dryer in combination with White Spirit. Heat the surface of the frame from a distance of 40 cm, pick up the edge with a scraper, then carefully begin to pull off the film with your hands.

When you have separated about 10 cm, spray White Spirit from a spray bottle onto the adhesive surface. Use a gauze cloth or scraper to scrape off the base and work your way down gradually.

After removal protective coating may remain on the glass and frame sticky marks. Wipe them with a hard cloth soaked in white spirit, and optionally use a rubber-tipped scraper.

Method No. 5. "Cosmofen"

Companies selling and manufacturing windows produce a product called “Cosmofen”. The main task the drug is cleaning metal-plastic structures from sticky formations after removing the film. The drug is available in different concentrations, it all depends on the number of active ingredients in the composition.

"Cosmofen" marked "No. 5" is considered the most effective, but it can dissolve plastic, for this reason it is recommended to be careful. Preparations numbered 10 and 20 are also produced, it all depends on the duration of exposure of the film on the glass.

To use the composition correctly, it is important to take into account the manufacturer’s recommendations. As a rule, after removing the film, the mixture is sprayed over the entire surface and then carefully removed with a cloth or scraper.

When working with the composition, be sure to wear safety glasses, a mask, and gloves. If possible, wear a long-sleeve robe.

Method number 6. Blade

Perhaps one of the most common options is film removal sharp knife or a blade. To do this, just pick up the free edge, and then gently pull the film under acute angle. It is possible that it will tear, take your time.

You can remove any remaining glue with a blade. The main thing is to pre-moisten the surface with any product that contains a solvent. Acetone, white spirit, industrial solvent, nail polish remover, etc. are suitable.

Do not press down on the blade to avoid leaving scratches. After removing most of the glue, clean the windows with dish soap and a stiff sponge.

Method No. 7. Paint remover

Buy at hardware store paint remover composition called “RP-6”. Use a knife or blade to pry up the free edge of the film and gently pull it down at an acute angle. Next, apply “RP-6” to the entire surface of the adhesive base, leave for a quarter of an hour (the exact time is indicated by the manufacturer on the packaging). While working with the drug, protect the skin of your hands, respiratory tract and eyes.

Remove excess with a dry cloth and prepare a solution. Grate half a bar of laundry soap, dilute the shavings into 3 liters. boiling water, stir. Dampen a rag and wipe the glass and frame until the glue disappears completely.

It is easy to remove the protective film from the surface of plastic windows if you use in effective ways. Consider cleaning the glue with White Spirit or an industrial solvent, remove it with an office eraser, blade, Cosmofen or RP-6. Follow safety precautions.

Video: how to remove old protective film from PVC windows

Reading time: 1 minute

Owners of plastic windows often do not know how to wash plastic window film. Indeed, this is not a simple matter. The film comes off poorly, traces of glue remain on the frame, and many owners are afraid to use more “radical” measures (solvents, scrapers). It is important to get rid of traces of film and preserve aesthetic appearance frames

There are several simple secrets How to safely and effectively remove the protective coating on plastic windows.

The price of tools and materials for film removal is low. However, it is better to peel off the protective tape from the window frames immediately after installing the double-glazed windows rather than spending a lot of time on it later.

The fact is that the protective shell consists of two layers. The bottom layer with glue is thinner. When exposed to sunlight and heat, the layer dissolves and is absorbed into the plastic. This is why simply peeling off the film from top to bottom is not successful. It will remain in your hands top layer, and the glue will still stick to the frame.

It will not be possible to quickly remove the protective film after a long time after installing the windows. Most likely, the entire process will take several hours. The shell can be removed using physical or chemical action. In most cases, both the first and second methods should be used.

Mechanical

Many new residents are interested in how to clean plastic windows from film. Often, after installing windows, builders break the rules and do not remove the protective tape immediately. The house may stand for several years before it is fully completed. During this time, the tape will “tightly” stick to the frames. In this case, it is better to resort to a mechanical method.

By using various instruments You can pick up the film and remove it from the surface. In this case, most likely, an adhesive layer will remain on the frame. It can also be removed using tools without resorting to chemical methods.

Information on how to remove the protective shell using tools can be found in the table.

Image	Tool	Instructions
	Household or construction hair dryer	1. heat up an industrial hair dryer (a household hair dryer must be turned on at maximum power); 2. carefully, without touching the glass unit, heat the film with a stream of hot air; 3. Using a utility knife or scraper, help yourself remove the protective tape; 4. Remove remaining glue with solvent.
	Scraper for hobs and glass ceramic hobs	1. pick up the edge of the protective shell; 2. Carefully guiding the scraper forward, gradually remove all the protective tape; 3. treat any remaining adhesive with a chemical.
		1. trim the film and pick it up with a stationery knife; 2. slowly, without making sudden movements, pull the protective shell towards you with your hands; 3. Using a knife, completely peel off the protective tape; 4. Wash off any remaining marks with a sponge and detergent.
		1. remove the protective shell by hand (as needed); 2. “erase” the remaining traces of glue with an eraser; 3. wash the frame with soapy water.
	Brush and soap solution	As with the eraser, if there is any glue left on the surface of the frame, it can be washed off with a stiff brush and soap.

The most effective is an industrial hair dryer. The hot air flow melts the adhesive layer, so the efficiency of complete film removal without subsequent surface treatment increases. It is worth noting that a household hair dryer is not well suited for this task. The power of a household hair dryer is not enough, so you will have to additionally “fight” with the adhesive layer.

Advice! If you are not confident in your abilities, then you should use the services of a cleaning company. Specialists will remove the protective tape without damaging the frame and glass unit.

Chemical

You can wash the film from plastic windows using chemicals. It is not recommended to use aggressive solvents, including alcohols, as such products can deform the plastic frame. In particular, denatured alcohol, White Spirit, RP-6 and Cosmofen will help get rid of glue.

It should be remembered that when working even with weak solvents, you should follow safety rules. Work must be carried out in a ventilated area or wearing a respirator. It is better to wear gloves to wipe off traces of glue with rags soaked in the substance.

Features of the use of chemicals on plastic windows are presented in the table.

Photo	Means	How to use
		Denatured alcohol or industrial alcohol must be poured into a small spray bottle and sprayed evenly over the protective tape on the frame. After about 2 minutes, pick up the edge of the film using a utility knife and pull slowly. In this case, traces of glue may remain on the plastic, which can be easily removed with acrylic solvent or white spirit.
		"Cosmofen" is a series of cleaners with a solvent or non-solvent effect, developed specifically for PVC windows. Cosmofen-10 is suitable for cleaning film. This is a weakly solvent cleaner that will help remove traces of glue from plastic frame, maintaining its integrity. Just wipe it off problem areas with a cloth soaked in the product. "Cosmofen" is recommended to be used in combination with a hair dryer.
	RP-6	RP-6 is used to remove old paint With different surfaces. The mixture is also suitable for getting rid of the protective shell on PVC. To work with RP-6, you must wear goggles and gloves. RP-6 is applied in a thick layer to the surface to be treated and left for 10 minutes. During this time, the film will rise and begin to lag behind the frame. All that remains is to remove the protective tape and treat the residue with a weak solvent.
		White spirit is a universal means for removing complex stains. This is a rather weak solvent, so it must be applied not on top of the film, but on the adhesive layer. To do this, just pick up the upper edge of the protective layer, pull it a little and pour the product into the resulting free gap. After a few minutes, you can easily peel off the film. If the film is long, then the procedure must be repeated until the White Spirit gradually dissolves the entire adhesive layer.

Advice! Also suitable for removing glue from plastic universal remedy"Shumanite." However, it is worth remembering that it contains caustic substances that can damage the PVC profile. Therefore, you should apply the product to the sticky surface of the frame and immediately wipe it off along with the glue.

Cleaning the glass

Many owners of plastic windows are also interested in ways to clean a window from mirror film. Special protection that reflects the sun's rays is sold in hardware stores. Residents of houses living on the sunny side purchase film for the summer. However, with the onset of cloudy days, it turns out that peeling off the protective layer is not so easy.

The problem is the same as with the protective tape on the frames. Despite the fact that the mirror film does not have an adhesive layer and is glued with water, under the influence of ultraviolet rays it practically eats into the glass unit. It can be very difficult to peel off such protection.

Advice! To solar protection for windows came off easily, don’t delay removing it. If the windows face south and the sun shines from April to October, then it is easier to leave the film or initially refuse to use it and hang blinds.

Simple methods for removing solar control film from windows:

• Using denatured alcohol and a spray bottle, similar to removing the film from the frame, you can get rid of the sun protection layer on the glass unit. Denatured alcohol is sprayed onto the surface of the window and left for several minutes. Then, using a stationery knife, pry up the edge of the shell and gradually remove the entire layer with your hands. It's better to start from the top.
• Using a steam generator, you can melt the surface of the sun protection layer, and then remove it by picking it up with a knife. This method is well suited for ingrained film that is difficult to pick up.
• Clean the glass unit with a sponge containing Schumanite. This strong remedy, which must be handled with gloves. You should also avoid contact of the product with plastic parts of the window.

Sometimes pulling the film off the glass unit is not enough. Often mirror-like, “silver” traces of the film remain on the surface of the window. You should not handle solvents: lavsan, the material from which the protection is made, does not come into contact with solvents. Everything is much simpler. Just wash the window hot water with soap, and rub the “silver” stains with a hard metal sponge. There is no need to worry about scratches on the window: the glass unit will withstand such cleaning and become as good as new.

The video in this article will clearly demonstrate how to remove protective and sun protection covers from plastic windows.

Film on windows - no global problem, which will definitely find its solution. Depending on the degree and duration of gluing, owners can use combined cleaning methods. The main thing is to remember the vulnerability of PVC structures and not to use aggressive methods.