As a rule, the bathtub is dismantled during repair work the entire room or when replacing plumbing equipment. In any case, you will need step by step instructions how to remove a bathtub so as not to damage the cladding elements, furniture and other plumbing fixtures in the bathroom, and to do the work quickly and efficiently.

Despite the fact that during the dismantling process you will still generate debris, preliminary cleaning and preparation of the room is a mandatory step before starting work. If this comprehensive renovation, then there should be nothing left in the room at all, including sinks and hoses. Experts recommend dismantling the bathtub wearing special clothing and protective equipment. You must be prepared for the fact that the work ahead will be quite soiled and dirty.

So, before you take it off old bath, you need to do the following:

1. Completely disconnect all communications in the bathroom: turn off all water supply taps.
2. Remove all bathroom fixtures and fittings. Even if they don't bother you, you still run the risk of getting them very dirty or hopelessly damaged.
3. Remove all furniture from the room: bedside tables, cabinets, etc.
4. Dismantle plumbing and sanitaryware.
5. Clear the room of anything that might interfere with work.

Quite often, dismantling a bathroom is directly related to a major overhaul, which involves removing tiles, tiles, stripping paint, and others. facing materials. Everything is mostly done quite quickly, but it will take you at least a day.

We also advise you to inquire in advance whether your home provides a service for removing bulky waste. Otherwise you will have to deal with the removal old bath independently, which can be quite difficult.

Let's start dismantling

When everything preparatory work done, you can proceed directly to dismantling:

• The first step is to disconnect the drain pipe. If your plumbing has been standing since the time Soviet Union, then most likely the pipe is cast iron connected with a concrete solution. Naturally, this design is firmly fixed. The easiest way is to simply cut such pipes so as not to waste time. In any case, you are unlikely to use them in the future. But plastic pipes You just need to unwind it and put it aside while dismantling it in another room.

• Before removing the bathtub, disconnect the floor siphon and overflow pipe. The siphon is in most cases secured with a coupling bolt turned towards the drain grate. Just turn it in the opposite direction and unscrew it. After this, the siphon can be disconnected without any problems. It happens that the clamping nut is difficult to unscrew. If it does not give in and there is no need for its subsequent use, you can simply cut it with a hacksaw. Such nuts are made mainly from soft brass, so special effort not needed for cutting. If it is inconvenient to work with a hacksaw, you can use a chisel and a hammer. Just knock it down carefully, being careful not to damage the tub itself.

• Now you need to make side cuts. They are made with inside drain grate so that the distance is sufficient to cut out a sector from the drain funnel. Its size should be no more than a quarter of the circle.
• Next, carefully saw the circumference of the funnel. The most important thing is not to damage the enamel. But this is only important if you are reinstalling the bathtub. If not, you can work faster and without much care. Push what is ultimately left of the drain with the edges inward, bending it with a chisel and hammer. Now the drain will pass through the drain hole in the bathroom without any problems, and you can easily pull it out.

• Disconnect the drain-overflow pipe and remove the outlet pipe from the sewer socket. To prevent water from dripping, the bell itself can be closed with a gag or simply wrapped with a piece of unnecessary fabric. If the bath was grounded, the strip should be disconnected so that it does not interfere with operation. To do this, simply knock out a metal wedge with a hammer. Some of the tiles at the edges of the bathtub also often have to be removed.
• Now you can free the bathtub from the cement adjacent to it. Again, if you no longer plan to use the tub, special care is not required. You can simply beat off pieces of cement. It is likely that it will fall off along with the enamel. However, if all the plumbing is to be installed back, you need to act carefully. The top layers of cement can be removed with the same chisel, but do this very carefully. Next you will have to work more subtly. You can use a knife, spatula or any other sharpened metal; all actions must be carried out extremely carefully. You can go over the top with sandpaper, but this also risks damaging the enamel, which will cause corrosion in the future. In any case, if the bathtub was fixed concrete mortar, then it is unlikely that you will be able to do all the work perfectly.

Features of dismantling different types of bathtubs

In general, the process is quite similar in all cases, but different weights imply certain features and cause some difficulties. Therefore, let's highlight key points process in each individual case.

Dismantling cast iron bath. The problem is that reusing cast iron bathtubs is usually not possible. Therefore, the main tool for dismantling will be a hammer, which will be used to break the bathtub.

Beating off pieces of a cast iron bathtub is a labor-intensive and very noisy process. As a general matter, we recommend that you warn your neighbors that certain time you will carry out repairs to avoid later complaints.

Cast iron is a very heavy material, but at the same time quite fragile if you work with force. Beat the pieces of metal as small as possible so that you can put them in bags and take them out of the house. The advantage of breaking down a cast iron bathtub is that it eliminates the need to hire special equipment for removal. The pieces can even be immersed in passenger car, take it to a landfill or sell it for scrap.

If you don’t want to work with a heavy hammer for many hours, you can use a grinder with a special disk attachment. The pieces will be smoother and more convenient for removal.

Important! Use tools at work personal protection: gloves, glasses, closed shoes.

About how to remove acrylic bath, special detailed instructions not required. It is quite light and fits through the doorway without any problems. It can also be cut and taken away without any problems.

It should be said that acrylic bathtubs Many people agree to pick it up, which will save you from additional hassle.

Dismantling a steel bathtub is almost identical in principle to dismantling a cast iron one. For sawing, it is enough to choose a strong circle and a grinder. But if the bathtub itself is small, weighs a little and fits easily into the doorway, then there is no need to saw it. You can even just take it outside. You can be sure that it will be taken away immediately.

Despite the general simplicity of the work, there are a number of nuances that must be taken into account in the work. Therefore, we bring to your attention a set of basic tips that will greatly simplify and speed up the process:

• If light bath and fits through the doorway, do not saw it. Save your own time and effort.
• When you remove a bathroom from the room that you will be installing back after renovation, it is better to cover the corners with mounting film so as not to damage the enamel if you hit it against the corners of the opening, etc.
• Be careful not to damage the parts from the fasteners. Try not to lose them. Without these elements, installing the bathtub again will be very problematic and it will not stand firmly. You'll have to go to the nearest one hardware store and buy new ones.
• We advise you to immediately replace all drain pipes during the repair. Even if they changed relatively recently. You can easily damage them, and after installation new plumbing the replacement process will be very complicated. Replacement will not greatly affect the cost of repair work, but will prevent additional costs energy and time in the future.
• We recommend treating pipe joints with high-quality sealant. It's more likely preventative measure, however, it will never be superfluous and will provide long term operation.
• Before removing the bathtub, it is best to remove the legs if possible. You'll most likely be placing it in another room, and the metal of the stands can cause serious damage to the finish. It would be safer to remove them and simply roll the bathtub on its side in a new place or prop it up against the wall.
• When you lift the bathtub vertically, it can slide forward on the tiles. To prevent this, you can lay a regular rubber mat under it. This will provide excellent adhesion to the surface and greater safety in operation.
• If one side is firmly attached to the wall, you can simply lift the opposite side and “drop” it onto the floor. But care should be taken to soften the blow: apply fabrics, rugs, etc. But if you live in an old house with weak floors, this method is strictly not recommended.

As you can see, the dismantling process itself is not complicated, but it does require significant effort and time. Therefore, soberly calculate your own time and energy. And only after the final repairs begin work. You can learn more about how to remove a bathtub by watching the video.

Most often, old cast iron bathtubs are replaced and steel baths, less often acrylic, since they are the most modern.

Let's take a step-by-step look at how to change an old bathroom and what you need to do it.

1) Choosing a bath

First you need to decide what kind of bathtub you want to replace. You can read how to choose a bath in. The most common types of baths:

- Cast iron. Traditional baths of the Soviet era. Currently, from a design point of view, modern cast iron baths have nothing in common with Soviet ones. Main disadvantage— cast iron absorbs a lot of heat from the water, as well as the weight of the bath and the complexity of installation.

- Steel. Lighter and easier to install. The disadvantages include the fact that the bathtub does not retain heat very well, as well as the susceptibility of the coating to scratches and chips.

— Acrylic (plastic). Acrylic is a very strong material. The bathtub, in turn, is strong, warm, and the paint does not deteriorate. These bathtubs come in various shapes and colors, which is why they are the most popular at present. We recommend choosing acrylic bathtubs.

2) Dismantling the old bathtub

Dismantling must be done using a dismantling tool: crowbar, chisel, hammer, screwdriver.

If the bathtub is attached to the side with tiles, the tiles must be chipped using a hammer and chisel.

The final step is to remove the bathtub legs from the floor covering. IN best case scenario you need to knock out the fasteners. In the worst case, you will have to knock out the legs from the concrete floor with a crowbar.

3) Preparing the floor for installing a new bathtub

It is necessary to completely clean the coating and level it. If you wish, you can tile the floor. We have already written about how to lay tiles in the bathroom.

After the tiles have dried, you can begin to final stage- assembly and installation new bath.

4) Assembly and installation of a new bathtub

— Assembling the bathtub frame / screwing the legs to the bathtub. Depending on what type of bathtub you have chosen, you need to assemble the frame (acrylic bathtubs) or screw the legs (steel and cast iron bathtubs).

— Installation of outlet connection and Installation of drain-overflow. Included with the bath drain pipes and connections. They must be attached to the bathtub according to the assembly instructions. It is worth paying attention to the fact that the connections must be tightened tightly, but at the same time do not overdo it so as not to break the thread.

— Bath installation. It is necessary to install the bathtub in place, level the slope of the bathtub by adjusting the legs.

— Checking the bath. Turn on the water, increasing the water pressure little by little to check the tightness of the connections.

— Screen installation. The screen should only be installed when you have ensured that all connections are waterproof.

As an example, we suggest watching the video: how to change a bathtub with your own hands

If you decide to do major renovation in the bathroom, then they must approach with all responsibility the decision and implementation of changing plumbing structures, such as replacing a bathtub, which has already lost its original appearance during use and will not tolerate “bullying” in the form of restoration. Such an action requires preparation and skill, so if you do not have such qualities, use the services of a specialist. Otherwise, before starting work, you should fully study all the equipment and identify the main points for yourself.

Choosing the right new plumbing fixtures

Replacing a bathtub always starts with choosing it. Of course, today there is a wide selection of a wide variety of models, the manufacture of which is more based on the use of various materials.

Cast iron baths

A classic choice for families who don’t want to “throw money away.” They are reliable and durable, but their significant drawback- this is weight. Installation and, after a period of time, subsequent dismantling of a cast iron bathtub is practically impossible to do alone. You will need not only the help of a specialist, but also just a physically strong person to remove such a bowl. It is precisely because of the large weight when replacing plumbing fixtures, which have been preserved since Stalin’s times, that the dismantling of a cast iron bathtub is carried out by an experienced team of specialists who carry out their work quickly and efficiently within an hour.

Steel baths

Lighter designs, but have a number of disadvantages such as the possibility of chipping the enamel when mechanical impact, as well as a limited selection of models. As for installation, the whole process involves attaching the legs with metal wedges and attaching the bowl itself. You can dismantle a steel bathtub yourself.

Acrylic bathtubs

The variety presented today is popular due to its light weight, the ability to retain the heat of water for a long time, as well as easy installation, because upon purchase you can receive a standard set of necessary fasteners. When replacing such a bowl with a new one, removal of such a bowl is carried out independently and, if possible, without outside help.

Do-it-yourself dismantling of old plumbing fixtures

Dismantling an old bathtub is quite simple and concise if you follow all the rules and sequence during the replacement process. Be fully prepared before you begin.

So, dismantling the bathtub involves preparing the following tools:

• hammer;
• screwdriver;
• pliers;
• a chisel or any other device to knock off the existing coating;
• adjustable wrench;
• a crowbar or any other device to move the bathtub.

Dismantling the bathtub is carried out in the following sequence:

1. At the initial stage, it is necessary to disconnect the water outlet that is connected to the sewer using an installed siphon. Also turn off all taps completely.
2. Using a chisel and hammer, beat off the existing plaster of the old bathtub - the tightness of the edges to the wall was previously achieved with ordinary putty.
3. Unscrew the plumbing fixtures in accordance with the existing fastening mechanism, which depends on the type of bowl and material used.
4. With additional assistance, carry out removal and removal of the bathtub. People's help is sometimes necessary simply for convenience, because in small apartments It is difficult to carry out such actions alone.

This completes the independent dismantling of the old bathtub. As you can see, if you have an idea about appearance siphon and chisel, the process does not present any difficulties.

Proper installation of new plumbing fixtures

After the old plumbing has been removed and removed, it is necessary to move on to a new stage - the installation of a new bathtub, which is carried out in the following sequence:

1. Before you carry out preparatory work in the form of clearing the place. Clear the area where the new bowl will be installed.
2. First, install the legs. They are often attached to the floor on special “pallets”, which guarantee an even and tight installation. Do not reduce the stated height of the legs, as this is necessary for ease of carrying plumbing work at the time of installation and during further operation.
3. Make a new trim and connect it to the drain using a rubber collar.
4. Install the outlet. To facilitate this action, place a rubber coupling in the socket and insert the drain pipe.
5. It's time to install the bath itself. Here it is also better to resort to the additional help of a friend, because at this moment two actions are carried out at once: connecting the siphon outlet to the bathtub drain and tightening the neck.
6. Install the overflow. Connect the hose and neck using a plastic nut and a wedge gasket. Connect the other end of the hose to installed siphon. Screw the threaded neck into the overflow hole and seal it.
7. Check all connections by filling and releasing the bath. If leaks are detected at the joints, tighten the threads, if possible using an adjustable spanner. It is recommended to use plumbing fixtures no earlier than 6 hours after installation.

Replacing the bathtub with your own hands is now complete. If you have any questions, use the advice or services of specialists; they can not only give complete and detailed advice, but also help with installation.

If you, like us, have a problem - removing the old cast-iron bathtub and replacing it with something else, then the question immediately arises: what is better to replace the old cast-iron bathtub. There are several options, the main ones: a new bathtub modern design, low bathtub, tray, shower cabin.

How to replace an old cast iron bathtub

If the bathroom is small, then it is best to purchase shower cabin.

Compact shower cabins 90*90 cm, as well as other sizes, can be bought cheaplyin various online stores. You can purchase shower cabins from the most popular brands according to the most low prices with delivery to different regions RF. The bestseller is the Mirwell shower cabin.

Many people have probably seen, while traveling, staying in hotels, boarding houses, etc., that there are installed in the bathroom simple pallets without cabins. And to prevent water from splashing, simple, moisture-proof curtains are used. This option is also very suitable for a small bathroom. But taking a closer look at the price, you can see that the cost of pallets is practically no different from the cost of cabins.

Due to the small size of the bathtub, it is worth refusing to install a new one standard bath. For those who like to soak in the bathroom, you can install a low corner bathtub, small-sized bathtubs, right-sided, left-sided.

Photo from the site nir-vanna.ru

Perhaps the cast iron bathtub can still be given a fresh look. To do this, first of all you need clean. There are many suitable cleaning products available. Such as "Sanox" - gel, "Cif", "Comet", "Deboucher", etc.

But it is very difficult to clean a heavily soiled bathtub. Simple remedies: baking soda, laundry soap are mainly suitable for constant cleaning of the bathtub. Large deposits can be cleaned with vinegar (advice from the forum): fill the bath with warm soapy solution, add 3-4 caps of acetic acid (200 ml of vinegar essence), leave for 2 hours (3 hours). Drain, rinse warm water. But this tip is suitable for a bathroom with a smooth surface. What to do if the bathtub already has cracks?

You can paint the bathtub. There are many tips for painting a bathtub yourself. You can seek the help of specialists. But I remember well the advice from my relatives who went through this procedure - never do this, but it is better to immediately replace the bathtub with a new one. Replacing an old bathtub with a new one is something many people living in old houses have to do.

Examples of installing shower cabins with and without trays, just trays in the bathroom

Today, bathtubs made from lighter materials with excellent strength properties have appeared on the market. During the replacement process, you will need to dismantle the old bathtub.

Dismantling "piece by piece"

The removed bathtub must be taken out of the room, but this is not always possible to do through a narrow doorway. The problem of dismantling can only be solved by cutting the bathtub into pieces. About this in our video.

Replacing with an acrylic bathtub

The old bathtub has been successfully dismantled, preparatory work has been carried out and the time has come to install a new bathtub. You can install a new cast iron or metal bathtub. It’s just that acrylic bathtubs are in demand among most consumers today. Therefore, we recommend watching a video about replacing a bathtub with your own hands with a modern acrylic model.

Restoration instead of replacement

If you don't want to remove your old bathtub and install a new one, check out next video. You can turn an old ugly bathtub into a snow-white bathtub with a smooth surface. To do this, you will need high-quality cleaning of the old product from dirt and grease. Roughen the cleaned surface with sandpaper, remove sanding dust with a vacuum cleaner and rinse with water. Close all openings. After which you can start restoration.

You can replace your bathtub yourself by simply installing an acrylic liner into the old one. This replacement method allows you to extend the life of old plumbing by another 15 years without dismantling. Watch the video to learn how to properly install the liner.