Every year, millions of people spend huge amounts of money to visit exotic places on the planet. You can recreate natural beauty in miniature by making a decorative indoor fountain with your own hands. The lively murmur of water has a beneficial effect on emotional state person. Moreover, it is impossible to take your eyes off her.
The design not only gives the room a luxurious look, but also humidifies the air during the hot season. To create a decorative indoor fountain with your own hands, it is not necessary to purchase expensive installations. The main thing is to be patient, use your imagination, pick up the tools and create miracles. First, let's look inside the structure to understand how it works. Then let's get acquainted with the types indoor fountains. And finally, let's look at step-by-step instructions for creating a natural miniature for your home.
The fountain is not only a decorative element. Since it wonderfully humidifies the air, it should not be installed near wooden furniture.
Why does water flow
“All rivers flow into the sea, but it does not overflow.” This is what it says in the most ancient book of humanity. We see confirmation of these words every day when snow or rain falls from the sky to the ground. The Great Designer launched the water cycle in nature. Imitating him experienced craftsmen created with your own hands a decorative indoor fountain that pleases the heart all year round. How does this system work?
The design is based on a unique water cycle in a closed system. They start it with the help of a power supply connected to it. It lifts the liquid upward, after which it flows gracefully into the collection bowl.
There are decorative fountains that use several identical containers. They are lined up at different heights, connected by tubes. By pouring liquid into the vessel located at the top, the system starts. Ordinary physics plus a creative approach and golden hands. The result is an exotic corner with the quiet murmur of water that calms the nerves.
How to create a decorative indoor fountain with your own hands: step-by-step instructions
Before you get started, you need to think about the size and location where the structure will be installed. For example, in small room It is inappropriate to place a huge fountain. And, conversely, in a spacious room, a miniature structure may go unnoticed. The decorative fountain is installed on the floor, wall or table. Much depends on the overall design of the room and the number of household members.
Depending on the movement of water, fountains are:
- Cascade - liquid falls along decorative steps or ledges.
- Closed - water moves in flasks or flat containers attached to the wall.
- Fountaining - the stream is directed upward, after which it falls into a miniature pool.
There are backlit options in the form of wall paintings that create a unique atmosphere in the room.
When choosing a location for the structure, you should take small children and pets into account. The main thing is that the structure does not disturb anyone.
But how to make a fountain at home with your own hands to fill it with exquisite exoticism.
Of course, you first need to understand how the structure works, and then collect the necessary items:
- suitable container;
- aquarium pump;
- flexible hose;
- waterproof glue;
- decorative elements (expanded clay, various sizes shells, colored soil, wood, ceramics);
- backlight (optional).
A vessel of any shape is suitable as a main bowl. The main thing is that water does not leak out of it. The upper part of the pump for a small fountain is equipped with a sprinkler. Since the dimensions of the structure are very small, there is no need to put on the tip. Otherwise, water will flood the surrounding area of the room.
It is quite possible to construct a miniature pump yourself, since the unit has a relatively low power.
Let's start the creative process
Those “who despise the day of humble beginnings” never achieve success. Therefore, having collected necessary tools and materials for construction, wise guys get down to business.
Let's consider a traditional master class on creating an indoor fountain with your own hands at home:
- Cut a piece of about 10 cm from a suitable hose (can be an aquarium hose). Its diameter should coincide with the tip of the pump.
- A pump is attached to the bottom of the tank using suction cups and connected to the tube.
- The resulting space is filled with expanded clay or stones, placing a tube between them.
- To give the fountain a presentable appearance, all elements of the device are carefully masked using all kinds of shells, pebbles or glass.
- Depending on the preferences and interior of the room, the design of the structure is carried out using various objects.
Stylish exoticism in the interior of the bedroom
A small tabletop fountain can be made from a flower pot with a diameter of approximately 25 cm.
To work you will need:
- durable container;
- pump;
- translucent balls or pebbles;
- aquarium plants;
- paints for painting on ceramics or glass.
Used for the base of the fountain. To give the structure a stylish look, the container is painted with special waterproof paints. To circulate the liquid, install a pump, make a hole and bring the tube up.
The bottom of the fountain is decorated with decorative balls, shells or pebbles. After filling the system with water, aquarium plants are placed inside. They give the design an exotic look and uniqueness. Simple scheme creating a design opens up wide opportunities for beginning craftsmen.
A stream gurgles in a fountain and without a pump
Perhaps only a few have seen natural geysers in all their glory. As you know, there are no pumps there and no electricity. But such a release of water causes unprecedented admiration. Of course, it is impossible to create such a phenomenon at home without electricity. However, there is a way out!
To build a miniature fountain without a pump, use:
- several containers;
- thin tubes;
- connecting adapters;
- sealant (if containers are made of plastic);
- decorative elements.
First of all, drill a small hole at the bottom of each bowl. Thin tubes are pulled through them, and then sealed cold welding. The procedure will protect the system from fluid loss.
Even the smallest fountain can transform the landscape of a dacha or private home beyond recognition. This decorative structure will definitely become a favorite relaxation spot on your site, because it will give you the opportunity to unite with nature at any moment. Do you want this to become a reality faster? There is nothing super complicated here - anyone can make a fountain with their own hands. Don't believe me? Then to your attention step by step instructions with a photo, following which you can quickly and without the involvement of professionals get an effective and functional fountain.
Choosing a fountain
First of all, you need to choose suitable option fountain for your site. We are talking about its dimensions, shape and materials. When deciding this issue, focus on the area and style of the yard of your dacha or private house.
Yes, for large plot it is better to choose a classic sculptural model that will become the center of the landscape composition. And for a modest courtyard, fountains in the form of small architectural forms are suitable: sea shells, fairy-tale heroes, houses, pots and other similar figures.
But you don’t have to buy a ready-made sculpture, because you can also build a fountain with your own hands. The simplest option is a structure made of stones. To make it, place large flat stones on top of each other, use an electric drill to make holes in each of them and string all the resulting products onto copper pipe- it is through it that water will flow to the top of the structure. Then close the gaps with small stones and treat the cracks silicone sealant.
Choosing a location
The next step is to decide where exactly on the site the fountain will be located. In order for a structure to fully fulfill its aesthetic function, it cannot be installed “anywhere” - it is important to choose the best location. And for this you need to take into account several nuances.
- Firstly, the fountain has no place in an area that is too open, since under the influence of active sun rays the water may begin to “bloom.”
- Secondly, the fountain cannot be placed among powerful trees - their roots can cause deformation of the tank and waterproofing. In addition, leaves, fluff, fruits and tree seeds will constantly pollute the fountain.
- Thirdly, the structure should not be too close to the house, otherwise moisture will fall on its walls with the wind.
- Fourthly, it is undesirable to place the fountain in the open wind so that its gusts do not “disrupt” the jets.
Thus, the ideal location for a decorative fountain is light partial shade surrounded by flowers and low bushes.
When you choose a place, proceed directly to arranging the fountain. It assumes phased implementation three main groups of work:
- tank preparation;
- pump installation;
- installation and decoration of the fountain.
Preparing the tank
In order for the fountain to be durable and solid, it is necessary to equip a special reservoir for hydraulic equipment and water. This is done as follows:
- Dig a pit of pre-calculated depth and the diameter you need.
Important! The depth of the reservoir should be below ground level so that the soil around the fountain bowl is not washed away and the base is not deformed.
- Place at the bottom of the resulting hole thin layer sand and carefully strengthen its side walls with bricks.
- Cover inner surface the pit is dense plastic film- it will prevent the passage of water.
- Secure the film along the top edge of the tank and seal the seams with frost-resistant silicone sealant. Place stones at the bottom of the pit, distributing them over the surface of the film. The stones should not be sharp so as not to deform the film.
- Install a small emergency drain near the pit to prevent the water level in the tank from rising.
Installing the pump
The fountain will not be able to work without the most important mechanism - the pump. It is he who is responsible for the continuous movement of water flow. General principle The operation of the pump is simple: water is discharged through a nozzle into the reservoir, then enters the pipeline, where it undergoes coarse and fine cleaning, and then the already purified water is sent back to the nozzle.
The quality of the fountain’s functioning directly depends on the type of pump:
- Submersible - works on the principle of a centrifuge and is located in the center of the fountain tank under water. It's cheap, but reliable device, for the installation of which no fasteners are needed - the submerged pump is quite heavy, so it does not budge on its own. It is suitable for small weak fountains.
- Surface is a more serious type of pump, which is installed not inside the tank, but on its edge on the surface of the earth. This device is designed for large fountains with complex designs.
Pipeline for pumping system can be constructed from plastic pipes. Their optimal diameter is 16 mm.
Advice. In order to enhance the operation of the pump, additionally install a pressure tank - it will guarantee constant pressure water flow.
Fountain decoration
After the main functional elements are installed, you need to take care of installing the fountain itself, or rather its upper part. If you are using ready-made sculptures, then they should have special fastenings for installation. But a homemade stone fountain is best installed on metal slats previously laid on top of the tank.
Then start decorating the structure. The fountain can be decorated with plants, different-sized stones, clay figurines, microsculptures and any other details that seem appropriate to you on your site.
Don’t forget about such an effective decorative tool as lighting. These can be underwater lights, light strips, floating lanterns, land lamps - here you are also unlimited. But remember that lighting structures must be completely sealed, and all their contacts must be protected from water as reliably as possible, otherwise it will be unsafe to use them.
When all work is completed, fill the tank with water and start the fountain.
As you can see, to make a beautiful fountain with your own hands, you don’t need to work hard or spend a lot of money. Do not deviate from the instructions, use quality materials and don’t be afraid to experiment with decor – by following these three simple rules, you will definitely get a functional fountain that will delight your eyes and set you in a positive mood for many years.
Which fountain to choose for your dacha: video
Fountain at the dacha: photo
Making an indoor fountain It won’t take much time, but you will be able to save a significant amount and, as a result, get a beautiful interior decoration. If you believe the practice of Feng Shui, then the location of the waterfall on the northwest side of the house will allow the family to live in abundance for many years.
DIY home fountain
The construction of small cascades that will decorate the interior should be carried out thoughtfully, since it is important to realize that there is nowhere for water to flow. This means that the liquid inside must be present in the same amount. In other words, cyclicality is required. Water accumulates in storage type containers. A pump is installed in the system to lift the liquid to the top of the waterfall, and from there it will freely penetrate back into the container.
To make the streams beautiful, several decorative obstacles should be installed along the flow path; pebbles, shells, etc. are suitable for this. To make your home fountain beautiful, you should make several thresholds with recesses. This will allow you to get the characteristic sound of falling water.
Preparing for work
To make a fountain with your own hands at home, you must first select a pump. The power of the device will depend on the height to which the water splashes. Everyone selects this value independently based on the design option. To build a fountain with water gushing upward, you will need a pump that will have more power and a regulator. And for a small cascade, an aquarium-type pump is enough to filter the liquid.
Before starting work, need to stock up:
- reservoir;
- tubes;
- glue;
- decorative items.
The storage bowl should be of a spacious size. It will perform its direct duties, collect liquid, and will also become the basis of the entire fountain. Some pebbles can be placed directly inside the container.
Pump manufacturing
Manufacturing a low-power pump It is quite possible for anyone to master it. To make it you will need to use:
- the motor from any object, and it must protect against moisture penetration;
- batteries;
- connector for charger, when using a mobile phone;
- several LEDs;
- toggle switch;
- electric drive;
- gears;
- small container round shape;
- waterproof glue.
Using a gear, an impeller is made that will supply moisture. You need to make a hole at the bottom of the container where you can insert the motor shaft. An incision is also made on the side for liquid. Install the motor shaft into the container, glue the main part of the motor to the bottom of the container, and attach the impeller to the shaft. Then a small piece of plastic is cut off, in which a hole is made, open area the pump is sealed. A tube is attached to the side hole and sealed. Then you need to connect the wires to the motor and insulate them using regular sealant.
When installing batteries, be careful not to allow moisture to get into them. The fastening is done on the outer part of the pool, and a toggle switch is also installed here.
Assembling the composition
To make a homemade fountain with your own hands assemble correctly, you need to attach a homemade or store-bought pump to the bottom of the storage tank. The depth of the tank must be selected so that the pump is completely immersed in the liquid. Masking the pump can be done in several ways, for example, by placing a mesh cover on top of which pebbles will be poured, you can also use shells.
You can use the dry fountain method, where the water is not visible on the surface. This is achieved by laying the lattice and securing the stones. Penetrating through the stones, the liquid will not form a visual pool; everything will accumulate in the container.
Can build fountains for home, using ceramic pots. This is quite possible if you follow some recommendations:
This miniature composition is placed on a table or in a special corner, next to indoor plants. Such a fountain can be an excellent addition to the decor, as well as an air humidifier in the apartment.
Original waterfalls
Vertical type waterfall is a stylish and fashionable decoration in any interior. It requires more time and effort. The difference in tabletop and vertical compositions is the pump, which should be much more powerful. When choosing a pump, you should pay attention to the pump; it should lift water to a height of about 2 meters. Thus, it is possible to achieve the arrangement of a waterfall, the top of which will be located right under the ceiling.
Before you begin the main work on constructing the fountain, you should take care of waterproofing the floor surface. You can use plastic film. It is better if it covers an area slightly larger than the capacity of the structure.
To prepare a panel that will be used to drain water, you need to use some materials. It is desirable that they be of high quality, and the life of the waterfall will be longer.
Install the pallet and attach the board on which the glass will be fixed vertically. Using support bars, a frame is knocked down onto which the crossbar is fixed.
Then make holes in the water supply not very far from one another to give the appearance of the integrity of the waterfall. If they are placed at a more distant distance, you will get several separate streams. Make a plug at the end of the tube and attach it to the top of the lid. If desired, provide illumination.
Place the glass panel in lower zone clamp and install in a vertical position. Using liquid nails, attach to the boards on the side. To prevent liquid from spreading, strips of glass or plastic are placed on the edges.
The pump is installed in a pan, a tube is connected to it to supply liquid to the top. After connection, the connection is treated with sealant. Hang the front cover. Then they move on to decorating the fountain based on their own preferences.
There is a huge selection of materials for decorating indoor fountains and waterfalls; you can purchase them at any pet store. Various flower boutiques sell bamboo supports, as well as original containers and reservoirs. By going to the souvenir shop, you can buy figurines and bonsai.
How nice it is to sit in a comfortable chair and enjoy a pleasant rest, watching the drops of water flow down. Fountain or home waterfall will please the eye, and the murmur will soothe and relax. If you place several living plants around the fountain, you will get a picturesque picture.
It is worth considering attractive additions that can decorate any structure. First of all, of course, we are talking about backlights. They can be different, with an iridescent effect. The most commonly used is an electric generator. To do this, you will need a small device purchased in a store; it will cope with the task and make the LEDs work.
Elements can be arranged in any quantity and in different places, the main thing is to remember that water should not get on them. After all, this is electricity, so it’s worth taking safety precautions.
Even the smallest body of water can decorate your own summer cottage and give it some zest. And a fountain made with your own hands will not only become a favorite place to relax and provide aesthetic pleasure, but will also become a reason for compliments from invited guests.
But not everyone decides to build this mysterious hydraulic device. Some summer residents mistakenly believe that building a fountain is a labor-intensive and expensive process and cannot be done without the help of specialists. But every lover of spending time in nature can give themselves such pleasure; the main thing is to know all the nuances of constructing a fountain with your own hands.
Choosing a fountain type
There are two types of fountains based on the type of design.
- The open version involves supplying water to the nozzle. The formation of a jet in this version of the device occurs due to changes in water level. In this case, the water pressure is weak, so it is necessary to constantly monitor the water level. In addition, the water in such a fountain becomes polluted quite quickly. To create it, you need to install a small reservoir at a height of about one meter above the nozzle.
- A fountain with a pump is the most practical and effective option. By placing the pump at the bottom, continuous circulation of water is ensured. Here the pressure is stronger and visual effect more beautiful.
By design, pumps that act as fountains are divided into submersible and surface (stationary).
The optimal place to place a fountain
When choosing a convenient place to build a fountain, it is recommended to take into account the degree of slope of the ground. If the area is uneven in shape, it is better to place such decoration in a low area. This option for the location of the reservoir will not only allow you to adjust the volumes groundwater, but will increase the oxygen saturation of the air.
- too close to the house so that moisture does not fall on the walls in windy weather;
- on open areas, in order to prevent water from blooming due to sunlight entering the reservoir;
- near trees so that leaves, seeds, fluff falling from them do not clog it, and roots do not damage the waterproofing.
The fountain must be positioned in such a way that it is not an obstacle to other buildings and is visible from all points. It is recommended to place the structure near the resting place.
The minimum distance that must be maintained between the fountain and plants, buildings, and furniture is 50 cm. This way, the plants will not die from excess moisture, and the furniture will not become unusable. The ideal location for the fountain is partial shade and a place protected from the wind, located close to a source of water and electricity. This arrangement will save you from unnecessary wires and additional work by isolating them.
Having decided on the location, it’s time to think about the shape and depth of the future fountain.
Preparation of materials for construction
To build a fountain in order to save money and effort, you can use the technology of constructing a decorative pond and equipping it with a pump.
Materials required to build a fountain:
- fountain container;
- pumping station;
- durable film;
- bayonet shovel;
- natural stones of various sizes;
- sand, gravel;
- decorative elements.
Selection and installation of capacity
If you plan to build a miniature fountain, you can use an ordinary plastic basin or any other small container as a reservoir.
For large bodies of water, old bathtubs or a self-dug pit are suitable. If a bathtub is used, it is necessary to dig a hole of such a size that its edges are not higher than the surface of the ground. All holes in the bathtub are securely sealed, after which it is lowered into the pit and strengthened with earth, stones and sand.
For a homemade tank, make a hole of the required depth and cover it with a thick, high-quality film, which is secured along the edges on the surface with stones. Stones of various shapes and sizes are also poured onto the bottom. It is important that the stones do not have sharp edges and cannot cut the film. The stones are evenly distributed along the entire bottom of the future fountain.
Choosing a pump for fountain construction
In order to construct a fountain on the site yourself, it is not necessary to purchase expensive materials, you can adapt any old elements. However, you should not spare money - the pump, the better quality it is, the more beautiful the fountain will be and the longer it will decorate the area without causing problems.
Submersible pump – best option for the construction of a fountain on a summer cottage. It works on the principle of a centrifuge. You can also install surface pump, it is mounted on the edge of a pond, but is most often used on large fountains and cascading ponds.
When choosing a pump, you should take into account the pressure that is constantly present in the pipe and the differences in this pressure. Therefore, purchasing the most powerful pump may not be justified, since not in all cases it will be able to work out its full power.
Regardless of which type of pump is chosen, it is important to remember that its power must be related to the diameter of the pipe. The fountain jet should come out under powerful pressure, and not slowly flow out of the pipe, since there will be no effect from such a design.
How to make a fountain with your own hands: step-by-step instructions
The construction of a fountain includes several main stages:
- pit preparation;
- securing the trench;
- installing a container or covering the bottom and edges with film;
- installation of pumping equipment;
- fountain decoration.
To build such a fountain you will need:
- an old tire from a truck or tractor;
- cement mixture, water, crushed stone and sand;
- a container for mixing cement and a shovel;
- sealant;
- building level;
- mastic;
- stones;
- pump.
Stages of work:
Video - DIY tire fountain
For such a fountain you will need to prepare:
- thick film;
- shovel;
- sand;
- pump;
- stones different sizes no sharp corners.
Stages of work:
- we dig a hole, clear it of stones and compact the bottom;
New life for an old bath
For this option country fountain you need to prepare:
- shovel;
- pebbles;
- pumping equipment;
- bath;
- insulating tape;
- metal scissors;
- non-ferrous iron sheet;
- drill.
Stages of fountain construction:
- we dig a pit corresponding to the size of the existing container;
- place the bath inside and plug all the holes;
- We cut out wide strips of iron and lay them around the bathtub, covering it with stones;
For this sprinkler you will need:
- plastic bottle;
- metal, strong wire or nail;
- insulating tape;
- garden hose.
Stages of constructing a fountain:
- Place the mini-fountain in the right place and turn on the water.
This option is perfect for watering your garden.
Decorative fountain for home
To build such a fountain you will need:
- big flower pot with pallet;
- paints for glass and ceramics;
- small water pump;
- contours;
- decorative balls, aquarium decorations.
Construction stages:
- decorate the pot with paints;
- make a small hole in the bottom of the pot;
- install a pump under the pan;
- we drag the pump tube through the hole made in the pot;
- fill the bottom with pebbles;
- decorate artificial plants and figurines;
- fill the pot with water.
Video - DIY decorative fountain
Fountain decoration
You can emphasize the uniqueness of a hand-made fountain by decorating it. It is recommended to lay out beautiful, colorful stones of different sizes around the pond, put flowers in pots, place cute figurines of animals, birds, etc.
To make the fountain amaze with its beauty and unusualness at night, you can backlight it using special equipment. Lamps installed around the perimeter of the fountain and lighting at its bottom will create a fabulous, magical atmosphere.
The bottom of the reservoir can be landscaped with the help of special plants, and bushes can be planted around the fountain.
Any country pond and fountain, including one, needs careful care. To maintain order and clarity of water and a pleasant spring appearance of the structure, it is necessary to regularly clean the tank. Using special devices, it is necessary to remove leaves, seeds, fluff and other objects from the surface of the water that can not only spoil appearance reservoir, but also lead to a malfunction of the fountain.
Upon completion summer season it is necessary to drain all the water, move the removable parts of the structure indoors, and cover the remaining parts and the bowl with film so that dirt does not get into them.
Building a fountain with your own hands in a country house or even in an apartment is not difficult and does not require large financial resources. Before you build decorative fountain you need to decide on the shape, size and installation location. There are many options for the location of such structures - near the gazebo, on the lawn, in the garden. After constructing the fountain, you need to carefully monitor the purity of the water, regularly remove debris and add water, as it will evaporate.
Such designs are widely used in design suburban areas. Fountains can decorate any ownerless area or become a highlight summer cottage. And by adding imagination and decorative elements, you can make it even more beautiful and unusual.
These days, mini-fountains are becoming increasingly popular, as well as decorative waterfalls. Such decorative elements allow you to relax, and in the summer they humidify the air, creating an optimal microclimate. Looking at the flowing water, it is convenient to concentrate, you can even meditate, if you are interested. The article will discuss a method for creating a simple waterfall, and the pump is also made by hand. The homemade product is easy to assemble and requires minimum quantity materials that are easy to obtain.
Materials and tools for homemade work:
- a small motor (can be found in a camera or phone);
- plastic gear (found in toys, watches, etc.);
- a piece of plastic a couple of millimeters thick;
- bottle cap;
- deodorant cap;
- foil;
- regular ballpoint pen;
- LEDs;
- resistor;
- wires;
- shells;
- mobile battery;
- a small plastic box.
Tools you will need:
- drill;
- scissors;
- pliers;
- hot glue gun;
- soldering iron;
- superglue;
- hacksaw.
Fountain manufacturing process:
Step one. Fountain device
To operate the fountain you will need a pump; here you can make it yourself. Its operating principle is shown in the diagram.
The number 1 indicates the hole for the liquid inlet.
Under the number 2 is the pump wheel.
3 is the pump body.
Well, the 4th pipe indicates the water outlet.
Step two. We prepare the motor and make the impeller
The motor should be small, since the mini-fountain will not be much larger in size than a pack of cigarettes. The author uses a camera motor for these purposes. As an option for these purposes, a vibration motor from a mobile phone is also perfect.
Next you need to do impeller, it is made from a regular plastic gear. These are found in toys, watches and other mechanisms. However, other materials can be used, the main thing is that the workpiece is suitable in shape and size. The gear needs to be ground in a circle to the size of the pump housing.
To make the blades for the wheel, you will need rectangular pieces of plastic. There will be 4 of them in total. The pieces need to be glued to the gear.
Step three. Pump body
The author makes the pump body from a deodorant cap. You need to cut off all unnecessary parts from it, and then drill holes as shown in the photo. You need to drill a small hole at the top so that the motor axis comes out through it. Water will come out through the large hole.
Step four. The final stage of pump assembly
To create the outlet tube you will need a ballpoint pen. You need to cut off all the excess from it, and then the handle is simply glued to the body.
As for the motor, it is also glued using hot glue. You need to glue the motor carefully so as not to fill it through the cooling holes and glue the axle. The impeller should be located evenly in the housing, it should not touch anything.
You will also need to make a cover for the pump. The lid is made from a bottle cap; you need to make a hole in it, as can be seen in the photo. Water will enter the pump through this hole. The lid is glued to the body with hot glue.
That's all, the miniature pump is ready. According to the author, it is capable of forming a water column 20 cm high, and all this from a 3.7V power source (mobile battery). This power is quite enough to create a miniature fountain or waterfall.
Step five. How to make a slide for a fountain. Final stage of assembly
Stone stylization was taken as the main idea. Here you need to use all your imagination. Externally, the fountain can be made whatever you want, at your discretion. You can ensure that no one can distinguish it from a store-bought one. To create the “stones,” the author used crumpled foil glued with hot glue. The photo shows the preliminary painting.
To make a decorative water source, you will need a shell suitable size and shapes. You need to make a hole in it for the tube. Well, then the whole structure is assembled as in the diagram.
