How to cut a 45 degree corner. Cutting the corners of the ceiling plinth: tools and cutting methods

The quality of the ceiling finish greatly affects the appearance of the room. That’s why they try to do everything perfectly, or very close to it. The finishing touch to the design is ceiling plinth. They give the finish a finished and holistic look. The planks themselves are easy to install on flat surfaces: using special glue white, but problems arise with the design of corners. Without knowing how to make the corner of a ceiling plinth correctly, a lot of material is spoiled. We’ll tell you how and with what to cut it in the corners.

What is it made of and what is it called?

The very first plinths on the ceiling were made of plaster. They were cast in special molds, then installed on the ceiling using mortar. Such figured decorations were called fillets. Today you can rarely see them: they are expensive, but in appearance they are almost no different from cheaper options. And this name is almost lost.

The most popular ceiling plinths today are made of polyurethane or polystyrene. They are inexpensive, look great, are easy to install, and have a wide range of profiles and designs. The width can be from 5 mm to 250 mm. They are used in almost any room, decorated in any style. Exception - Most often used here wooden crafts— style dictates its conditions.

There is also a similar plastic finish. It is mainly installed in bathrooms. But even in damp rooms you can safely install polyurethane strips - they are not afraid of dampness.

You need to cut ceiling plinths in corners from any material using one of the methods described below. The only exception is plastic skirting boards: such a corner can only be created using ready-made corners.

What and how to cut

Working with skirting boards from different materials implies the use different instruments for cutting. When working with wooden ceiling plinths, it is more convenient to use a wood saw. All others, including plastic, foam and other polymers, are better cut with a metal blade. This results in a smoother cut and less burr. Saws are usually used when working with a miter box.

When working with foam baseboards without special tools, cut them with a good stationery knife. Its blade is quite thin and even, the cut is smooth and not wrinkled. If you work with polyurethane or polystyrene with a saw, do not press hard: you can dent it.

In general, to get a little used to the tool and material, take a piece and practice on it: cutting, sawing, trimming. This way there will be fewer problems during work.

How to get the right angle

The most problems when working with ceiling plinths arise when decorating the corners. Since the surface of the products is complex, simply cutting at the desired angle will not work: it is also necessary to trim so that they fit together and, preferably, without large gaps. In fact, there are several ways to make the corner of the ceiling plinth ideal (or almost).

Using a miter box

If the corners and walls in the room are smooth, you can use a special carpentry tool - a miter box. This is a gutter in the shape of an inverted letter “P”, in which lines are marked for cutting at an angle of 90° and 45°. The part to be cut is placed inside, and a saw is inserted into the guides. The part is held in place and cut at the required angle.

In the case of baseboards, not everything is so simple: they must simultaneously adhere to two surfaces, so they need to be pressed against one or the other wall of the miter box. When working with ceiling ones, they are pressed against the side closest to you.

The sequence of actions when finishing the outer corner is to make a cut at an angle of 45 degrees. Place the miter box in front of you. You try on how the plinth will be positioned, determining which part of it will be attached to the ceiling. In order not to get confused and to cut the ceiling plinth correctly, place the plank that will be located on the right on the right, and the one on the left on the left.

Press the part that ends up on the ceiling to the bottom of the miter box. The second side is closer to you and raised. You rest it on the wall of the device so that it does not wobble when cutting. That is, the front part of the plinth turns away from you. Make the cutting direction as shown in the photo below. By putting the two cut pieces together, you get a protruding corner - an outer or outer corner.

How to make an outer corner of a ceiling plinth using a chair

First place the sawn parts in place “dry”, without applying glue. If the geometry of the corner turns out to be not so ideal, you can correct it a little with a knife. It is easier to cover up small errors with special putty.

The situation with the inner corner of the ceiling plinth is very similar. First, try on which side will be on the ceiling, press this part to the bottom of the miter box, rest the second part on the wall closest to you and make cuts as shown in the photo below.

And again, first try it on without applying glue, and if necessary, adjust it slightly. Then apply a thin bead of glue to both surfaces that will be attached to the wall or ceiling.

Your version of how to use a miter box correctly is shown in the video.

How to make a corner of a ceiling plinth without a miter box

Few apartments or houses have angles exactly 90°. Small deviations can be easily corrected after trying on. But not always. Then you have to mark everything “in place” - under the ceiling.

You will need a finely outlined pencil (hard - it is not so visible on the ceiling, but leaves fairly clear marks close up), a small piece of plinth, a ruler and a good stationery knife if you are working with polyurethane (polystyrene) baguettes or a metal saw for working with other materials.

Place the plinth against the corner and draw along the outer edge with a pencil. Apply to the other side of the corner and also mark. You have a cross on the ceiling, the center of which marks the place where the ceiling plinth strips should meet (look at the photo). Having placed a piece of plinth in the corner that will be glued there and resting its end against the wall, transfer the mark to it.

How to make corners on ceiling plinths without using special tools

Now take a ruler and connect the edge of the baseboard with the marked mark. If you just put the plinth on the table and cut it along the line, the two parts in the corner still won’t fit together: it will get in the way inner part. It can be trimmed later by trying it on the ceiling. The second way is to install the piece that needs to be cut on the table with the part that will be on the ceiling. And cut along the line, but holding the knife at an angle of about 45°. You will still need to make adjustments, but much less (and less likely to make mistakes).

Repeat the same operation with the second bar. You attach it to the right wall, rest the end against the adjacent wall, mark the place where the cross is drawn, draw a line and then cut it off. Adjustment is carried out “dry” without applying glue.

You repeat exactly the same steps for the outer (protruding) corner. Now you know another way to make a corner of a ceiling plinth, without a chisel or other special devices.

Using decorative corners

There is another, easiest way. For skirting boards made of polyurethane or polystyrene, use ready-made, factory-made decorative corners. They are installed in a corner, and the strips are glued tightly to them. Trimming them if necessary is very simple: a few millimeters with an ordinary stationery knife.

How to join in corners

If the installation of the first corner is completed, you can assume that you have already learned how to do almost everything. “Almost”, because you still need to learn how to connect the corners and cut the planks to length. When some part has already been glued and there is a small distance left to the corner, how can you not make a mistake with the length? The answer is simple: leave a reserve.

At first, you can cut a piece 10-15 cm longer: you will have the opportunity to redo it several times if something doesn’t work out right away. Then you make an angle in the manner described above, try it on dry, adjust everything so that the result suits you. Only after this can you place the already cut strip in the corner and mark the place to which it can be shortened. You need to cut exactly 90°. It is not necessary to use a miter box. Just try to place the knife (hacksaw) perpendicular to the surface.

Sometimes you need to cut a particular part or product at a certain angle. As a rule, you need to cut baguettes, fillets, platbands, baseboards and other similar interior elements at an angle of 45 degrees. Anyone can cope with this task. The main thing is not to rush, don’t be nervous and everything will work out.

Buy ready-made corner elements

Of course, the easiest way is not to bother with trimming this or that part, but to buy a ready-made one that does not need processing or trimming. Such parts and elements are sold today everywhere in large supermarkets or smaller stores.

For example, as for baguettes or fillets, special corner elements are sold for them that fit perfectly into the corner and do not need to be trimmed. They just need to be glued into place and pressed well.

Method of joining platbands without trimming

Today, platbands are often not cut at an angle and then joined together, but the joints are made at right angles. This method of connecting platbands does not require any special trimming, which is very convenient. In addition, this method looks more modern and attractive.

Cutting at an angle using a miter box

If you still need to cut this or that part at an angle, then you should stock up on a miter box - a simple device that looks like a small box. The miter box has slots that are designed for a saw or long sharp knife. Of course, these slots are made to form a smooth and precise 45 degree angle.

However, a miter box can have many slots at once, under different angles. This is convenient because with the help of one device you can trim any parts at different angles.

There are adjustable miter boxes on sale. The slots in such a miter box can be adjusted, which allows the master to set exactly the angle that is required at the moment. In particular, it is quite simple to move the slits of such a miter box to a position of 45 degrees.

Now you can trim the workpiece simply. A baguette, platband or plinth is placed in the miter box, after which a saw is inserted into the slots and the excess is simply cut off. The angle ends up being perfect, exactly 45 degrees.

What to do if there is no miter box? Very simple. You need to make a template according to which it will not be difficult to transfer the necessary markings to the workpieces. As a template, you can choose thick cardboard or anything else that will be appropriate for your project. in this case.

Cutting parts at an angle using a protractor

You can cut the part at an angle using a protractor. This is a measuring tool that is easy to use, and which is designed specifically for measuring angles or making the necessary markings on certain parts. The protractor is applied to the part, the angle is marked and the markings are made with a pencil. Using these markings, cutting the workpiece at the desired angle will not be difficult.

Using Templates

If you don’t have a protractor, miter box or ready-made corner elements, you’ll have to look for a suitable template. Of course, the template must have the desired angle. It is applied to the workpiece and the workpiece is marked with a pencil. This is one of the most simple ways achieve the desired result.

Trimming "on the spot"

The walls, floor and ceiling will not always be perfectly flat in practice. Most often they have irregularities. For this reason, there is no need to cut the workpieces at clear and precise angles, because anyway they will not fit perfectly.

Instead, it is sometimes convenient to trim the same ceiling plinth in place. That is, first they glue one strip of the plinth, trim it in the corner, and cut the second strip under it.

Of course, it is hardly possible to cut the workpiece perfectly. However, if a small gap appears in the corner, it can always be covered with putty or gypsum plaster. Nothing special.

Video: How to cut the corner of a plinth or baguette without a miter box

Typically, the installation of foam or polyurethane ceiling molding, as well as the installation of floor plinths, becomes the final stage of repair work. And if gluing fillets on a straight surface is not particularly difficult, then you will have to work hard with the corners, especially when there is no skill and little experience. With all this, the joining itself is not a difficult matter; the main attention and diligence is given to cutting the sticks at the desired angle, which, by the way, can be external or internal.

Subtleties of the upcoming task

The most difficult thing is with the external joints. But even in this case, you can make a neat decoration of the room on your own and in two ways:

• The first is to purchase special fittings, which, in general, eliminate the need to cut the baseboards. This is the simplest solution to the problem, because both external and internal corners with grooves are available for sale, into which the edges of the stucco molding are inserted.
• In the second option, the corners are cut using special tool, called a miter box. Its use ensures an even and tight fit of the planks to the surface. By the way, you can simply make markings on the baseboards and cut the product with a metal file or a sharp knife.

We use a miter box

Using a miter box to cut fillets

This tool was originally created for cutting finishing materials, which subsequently need to be mounted at a specific angle. Appearance Such a device and its design may differ slightly depending on the model, but the principle of operation remains the same.

So, for example, by cutting a ceiling plinth, future angles can be adjusted, and the simplest version of the tool is a wooden tray with vertical slits on the walls. They are needed so that it is possible to insert a hacksaw and make a cut at an angle of 45 or 90 degrees. If desired, you can make a miter box yourself.

A slightly more complex modification is a tool that allows you to make cuts at an angle of 60 degrees, or position the file at an angle of 45 degrees. Professional repairmen use a miter box with rotating mechanisms, which allow you to secure the hacksaw as needed in each specific case.

Instructions for cutting skirting boards

Tools for cutting skirting boards

Before you make a corner on the ceiling plinth with your own hands, it is recommended to study the simple instructions:

• To cut corners, the baguette is inserted into the miter box, the desired cutting angle is selected, then a file is installed in the corresponding slot in the wall of the tool, and you can cut;
• A similar procedure must be done with the other fillet, only the corners must be cut using the opposite cut in the wall of the tool, but at the same angle.

Please note that you do not need to immediately cover the baseboards with an adhesive mixture and mount them on the ceiling. To begin, eliminate all cutting inaccuracies by connecting the parts and checking whether they form a perfectly straight joint. To add to everything else, the outer and inner corners for the ceiling plinth are cut differently.

If we are talking about cutting a plinth to create an external corner, then:

Trimming adjacent fillets for outside corners

• The bar that will be attached to the left should be on the side of the miter box closest to you, and lie with the bottom up. The hacksaw should be inserted into the farthest right and closest left cut;
• The bar that will be attached to the right is placed in the same way, only the hacksaw needs to be inserted into the far left and near right cut in the wall of the miter box.

In the case when you need to refine the inner corners, proceed as follows:

Trimming internal corners of ceiling plinths

• The strip that will be glued to the left should lie with the bottom side up and on the near side of the miter box. The cutting tool is inserted into the far left and nearest right cut.
• The baguette that will be mounted on the right is placed in the same way, only the hacksaw should be inserted into the far right and closest left grooves.

What to do if there is no miter box?

Cutting skirting boards without using a miter box

Now we offer an option on how to cut the desired corner of the ceiling plinth, if not the right tool. In this case, you can make a marking and then use a file or knife along it. To begin, prepare a ruler, a pencil and a stationery knife, and the process itself is as follows:

• Initially, the corner of the room itself is measured, for which it is enough to attach a baguette to it and make the necessary notes on it. Usually it is equal to 90 degrees, but there are also errors.
• You need to apply a ruler to the baguette at an angle of 45 degrees, and cut off the excess part with a precise sharp movement. If you have to work with harder materials, such as wood or polyurethane, you will have to electric jigsaw or a hacksaw, and cut along the line drawn with a pencil.
• Be sure to check whether both cut strips form a right angle, and only then start installing them under the ceiling.
• In the case when the angle of the wall is uneven, you need to measure it and divide the resulting value by 2. This will be the required indicator for applying markings to the baseboard.

Uneven corners can be corrected using sandpaper, or trimmed a little to the desired position, but for a ceiling plinth with a large error in the straightness of the angle it is difficult to come up with something, and it is better to start cutting new planks.

After reading all this, it may seem that you won’t be able to cut the required corners yourself. But if you carefully read all the recommendations, it turns out that everything is much simpler and faster.

How to cut the edge of a ceiling so that the corners are perfect

In the corners of a room, when installing edges such as foam, there may be slight inconsistencies that can damage general form rooms. Of course, this can and should be avoided.

So, how to accurately cut a stand with your own hands? The first assistant in this case will be both a tool and a chair. But a one-time purchase is not always recommended. Although, if you decide to help with renovations for all your relatives and neighbors, and then earn more money about it, you will need this device.

Example of ideal angles

If you are still limited to one mounting fabric at home, then such carpenter tools are not needed.

How to cut a corner on a ceiling that rotates indoors and outdoors using chairs

This can happen without him. To explore all the ways correct circumcision edges of the ceiling, we will know what it is made of.

Composition and characteristics of the material

To understand how to properly coat a footer, you need to understand its composition. This will help you choose the right cutting tool and technology.

• Styrofoam. The price and strength of this material are the lowest. But since we are doing decorative decoration on the ceiling, power is not particularly needed.
• The ceiling floor made of polystyrene foam is denser.

  like plain polystyrene. The most common knife is used to cut such material.

Tip: Use a knife before use. This eliminates the presence of ragged edges at the cut points.

How to iron surfaces smoothly

• Tree. It will take more effort. Use wood wire only.

Tip: Smaller and more frequent tooth saws, smoother edges.

You can also use sheet metal for metals.

• Plastics. How to cut a plate? Here the cable car goes the same way as a tree - a saw. You can still use Bulgarian.

With regular saw blade

Cutting methods

The product is arranged around a period of rectangular space.

Trimmed to full corners. That's why we'll look at how the sidewalk should be cut at 45 degrees.

Cutting using chairs

What is dirt?

This is a special tray made of wood, aluminum or plastic with guaranteed grooves that guide the saw at right angles.

Here quick guide for using this tool:

• Preparation. Take the product and insert it into the tray. Align where it will be installed on the ceiling.
• Cutting. On the other hand, insert the cutting tool into the groove.

  This could be a knife or saw. And he bravely went broke. The device does not allow you to miss a planned location.

You should know: Metal canvas is suitable for cutting foam.

• Treatment.

  Woodworking may need to be finished using a smooth cut file. Plastic or polystyrene can be repaired with a knife, but the main thing is that it is sharp enough.

Advice. Do not press the device while cutting. The polystyrene may deteriorate and the wood may thicken.

This is such a simple and easy to use chair

Cutting without seat

If you don't have such a device and don't buy one to use at one time, you can use the following methods to shorten your leg by 45 degrees.

1. The first way is to make this simple carpentry tool yourself.

   To do this, the most common tree tray is destroyed. Then measure the hash lines with a backboard or school square. We cut furrows and had a primitive setup.

1. Another way. How to reduce a surface at an angle is even easier. In particular, it should be used without pain in cases where the corners of the room are not equal.

We don't need a tray.

There are many two plates with a drop below 90 degrees and a cardboard pattern with the orientation oriented.

1. Third way. In this case we don't remove anything, but we use a table or some other similar structure attached to the wall.

Future connection points are marked directly on the product itself, on the wall and on the ceiling.

Place the footer when we intend to install it and cover it with labels.

The easiest way without using special tools

One thing to remember: when cutting, hold the tool strictly vertically to get the correct angle.

Cutting characteristics of various angles

We shared a common technology on how to cut sliding plates.

However, it also comes in multiple shades that cut different angles of this product.

Inner floor

Type internal corner

First, place your left and right legs at right angles.

The left product was placed in mud, which refers to outside, which cuts the left inner corner. Then we perform the same operation on the right one. Ready.

Open floors

External corner view

In this case, using the chair, we are not the inner edges, but the outer edges. The rest of the operation is similar.

External ceiling

External ceiling type

The corners are already inside the device.

Insert your left foot into the dirt, cut out the left outer corner. Set the right path to the right outer edge.

Internal ceiling

Type of internal ceiling corner

By analogy with outer corner we cut out the inner one.

Cut the inner left and right edges correctly.

It is important to remember: the ceiling is always attached to the ceiling. So paste it into an overloaded style. This will help you align your footer correctly.

• The booth stand should only be installed when it is ready.

  It's better on the ground, not under the ceiling.

• Patience, patience and patience. Sometimes connections need to be repaired more than once. Don't be nervous, be careful and it will all be over.
• By using foam and plastic, you can afford to leave small slots in the corners of the corners.

  Whales hide them. Be careful with the tree.

results

Efforts are bearing fruit

If you have any questions, the visual in this article will help you solve them.

Choose the method you like and go! Everyone gets you (check out the benefits of PVC base).

Ceiling plinth, how to make a corner, how to correctly cut the corners of a ceiling plinth, tools for trimming (cutting) the plinth, joining the ceiling plinth in the corners

Installing a ceiling plinth only at first glance seems like a very simple task.

In fact, you may encounter small and not so small problems that can not only exhaust you, but also completely discourage you from doing repairs. One of these problems is joining the ceiling plinth in the corners.

Quite a few copies were broken by ordinary apartment residents over the question of how to make the corner of the ceiling plinth, because it cannot simply be cut at an angle of 45°.

What to do in this case? Let's turn to professionals for advice.

How to make a corner of a ceiling plinth, how to properly join and cut the plinth

Yes, the main and most insidious nuance in the technology of installing ceiling plinths is how to properly cut the plinth and join it at the internal and external corners.

The fact is that, unlike ordinary skirting boards, ceiling molding It is attached to the base at an angle of 38-45°, which makes it difficult to make a classic 45° cut at the joints.

WITH inside the cut edges do not meet, leaving gaps.

The secret to successful cutting is that the baseboard must be cut not only along the outer edge, but also from the front side (or from the inside, if we are making an outer corner). The video will tell you in more detail how to cut the corners of ceiling plinths. The master used a professional miter saw, but you can get by with home tools.

After completing the procedure, the texture of the cornice should be clearly visible on the front or back side of the cornice. But these are all complex professional lyrics. How to make a corner of a ceiling plinth at home?

The easiest way to work is with foam accessories. First of all, measure the angle between the walls. If it's 90° or so, cut the edges at a 45° angle. Do the same with the second cut. For uneven joints between walls and ceiling, the corner radius is divided by two. Do not confuse the parts with each other: the baguette that will be glued on the left should have a cut on the right side, and the right fillet on the left.

To create an internal corner of the plinth on the ceiling, its lower part should protrude above the upper; for the external corner, the opposite is true.

Thanks to their soft and pliable texture, it is not necessary to adjust polystyrene foam fillets to each other, but you will have to tinker with plastic or wooden ones. After making the side cuts, try the planks on the ceiling and, if necessary, cut them in accordance with the direction in which the accessory joins the surfaces.

After rough joining the ceiling skirting boards, screw or glue the fillets to the ceiling and wall, and then seal the seams.

How to cut corners of ceiling plinths, tools for trimming and cutting corners

To cut the corner of the ceiling plinth, you will need certain tools.

If you want to make joints as well as a seasoned repairman, then an electric miter saw or miter box will be useful to you. With the help of these devices it is possible to achieve high precision cut. There is no need to make any effort. You just need to set the necessary parameters and omit sharp blade saws on a plastic or wooden surface.

You can cut the ceiling plinth more economical materials such as a hacksaw or a hand miter box. A simple saw is very cheap, and it is extremely easy to operate.

The only drawback of this device is its roughness. There is always a risk of spoiling the material. If you bought plastic or wood of poor quality, then during operation the product may begin to crumble or delaminate into fibers.

A jigsaw will help you make a corner on the ceiling plinth without burrs.

The advantage of this tool, in addition to high accuracy and efficiency, is also ease of operation. The jigsaw can be set to any direction of movement and make the highest quality cuts.

But these are all products that help solve the problem of how to join a ceiling plinth made of wood or PVC.

To work with foam plastic, use this complex equipment doesn't make sense. An ordinary construction knife will do here. The main thing is that it has a well-sharpened blade, then you will be able to make a high-quality cut without tearing or delamination of the material.

Still haven't decided how to cut the ceiling plinth? No problem. In stores you can find fillets already prepared for joining in the corners.

In this case, the opposite principle applies. When working with such a plinth, you need to make not oblique, but only straight cuts to connect the parts frontally.

How to make a corner on a ceiling plinth

True, the cost of such accessories is higher compared to classic ones.

How to cut corners of ceiling plinths

In order to start cutting the corners of the plinth, you need to acquire a tool such as a miter box.

This device adjusts the desired angle for cutting with a mounting knife or spatula. Its dimensions depend on the complexity of the work being done. For installation plastic construction It is enough to use miter boxes with low inclinations of up to 90 degrees. The most difficult point here is, perhaps, joining all the elements so that there are no gaps between them. First you need to make a sketch. The plinth is placed directly on the wall. If you don’t have a miter box on hand, you can get by with a regular stencil. The photo shows the process of cutting a small piece of foam with a knife.

How to make a corner on a ceiling plinth

In order to make a corner on the ceiling plinth, you need to acquire two important elements.

This is the material you will use to glue the ceiling, as well as a measuring ruler with which you can measure the corners on the ceiling. If the wall is smooth, then, as a rule, no special problems arise with measurements, but if there are gaps on it, then you cannot do without improvised means.

It is better to pre-treat the corners with sealant; sometimes painting may be required. It is important to remember that you first need to decide on the angle of the product, and then carry out the following operations, such as cutting out a ceiling corner.

In the diagram you can see a hint on how to make corners correctly.

Ceiling baguettes

Ceiling baguettes are special decorative strips for the ceiling, which can be decorated in various elements. Such a product can give the surface a beautiful aesthetic appearance. Most often, the baguette acts as a cornice and is used in theaters and other buildings of cultural education.

However, now you can buy varieties of it in stores for home use. Most often the product acts as additional element. Its design can be different, both the inner corner of the plinth and the outer corner of the plinth. Baguettes are recommended to be installed by experienced repairmen.
The figure shows one of the types of ceiling baguettes.

How to cut ceiling skirting boards in corners

In order to cut ceiling skirting boards in corners, you need to have a few important building materials and follow certain important rules:

1. measure with a pencil required length ceiling in which you are going to lay the plinth.
2. Using a miter box, you need to measure the length to which you will lay the corner of the plinth and cut the corner.
3. draw up a rough layout with length measurements and cut directly with a mounting knife.

Miter boxes can be purchased at any hardware store your city.
In the figure, mark the area whose corner needs to be trimmed.
Watch the video for more details:

Ceiling fillets

Ceiling fillets are now gaining wide popularity due to their ease of installation.

To begin installation, you need to measure the perimeter of the room using a regular ruler. We divide the area by approximately 2, depending on the area of ​​the room itself. You need to decide how many fillet strips you need to take. You can glue them in two ways: using glue or putty.

In the first option, you will need a flat surface of the wallpaper; for the second, we cut the corners of the PVC baseboard with a stationery knife, and then strengthen the products with putty.

How to cut a ceiling plinth

In order to cut the ceiling plinth, you need to use a miter box.

If you resort to professional repairs, then you can buy the simplest option with a narrow range of corner radii, from approximately 45 to 90 degrees. In order not to be mistaken about how to cut the plinth, draw a layout.

This can help, for example, when installing a plastic product. It is cut off with the very edge of the miter box; if there are uneven edges, they are sawed off with a mounting knife. For plastic skirting boards, it is advisable to measure out several pieces of stucco molding, and then start separating them. You can use a regular saw to cut the ceiling plinth.

What are corners for ceiling plinths?

Corners for ceiling plinths, or, as they are also called, baguettes, are special pieces of plastic that have a decorative finish.

In everyday life you can also come across such a name as ceiling cornices. They were originally used for decoration in buildings of cultural importance, but over time their use expanded to simple finishes at home. For corners, it is also necessary to first measure the length of the ceiling. Corners are most often made of polystyrene and have a dense texture and structure.

In order to install such baguettes, concentration and attentiveness are required. Installation is not much different from conventional ceiling finishing.

Corners for skirting boards come in various shapes. Their main feature is decorativeness and protection of the outer corner.

How to join a ceiling plinth

We will give you some tips on how to properly join ceiling plinths.

And it doesn’t matter whether you have a narrow or wide ceiling plinth. In order to start joining each piece, you need to place one piece of foam baseboard on the diameter of the wall and draw a line with a pencil to the other corner. This way you can measure the joint of the ceiling plinth and its corner connection. Next, you need to place the fillet directly on the corner (not on the mark!), and use a regular stationery knife to cut it.

For a successful connection, use sandpaper blocks. The corners are assembled directly into monolithic structure and one color.

What is a wooden ceiling plinth

Wooden ceiling plinth - variety decorative finishing for the ceiling, which allows you to hide visible unevenness of the wall and add attractiveness to your room. In addition to standard plastic products, there are also wooden ones.

You can get them at the warehouses of logging factories, or at a regular hardware store. You should only choose one that will match the decoration of your home. Be sure to purchase nails or screws to hold wooden cornice ceiling.

Installing these elements takes some time, but the installation process itself is not as complicated as it seems.

You need to carefully file down the pieces, cut out the corners, and process the areas of future joints. You will need various tools and accessories to cut wood. The joining technique is practically no different from other types of similar products.

The main thing is to carefully read how to calculate and how to adjust all the joints. Then the connection will proceed without problems.

How to join skirting boards

In order to begin the process of joining skirting boards, you need to prepare several tools:

1. pencil for measurements;
2. docking stationery knife.

First, measure the length and perimeter of the ceiling and mark it with a pencil.

If your surface is flat, you can get a regular miter box. The device is used when laying skirting boards at small angles, approximately 90-120 degrees. One strip of the product is placed under the miter box and cuts are made with the help of a knife in order to form grooves for the arrangement. A docking utility knife is used if the corners of the ceiling are not even.

What is a foam baseboard?

Foam skirting boards have found wide use for ceilings. Such products are now readily available and can be bought at absolutely any construction market. Polystyrene foam has good decorative properties. This type of plinth is usually supplied in pieces. To secure it, several objects are used, such as a miter box, a stationery knife.

In order to measure the length, you can get by with an ordinary well-sharpened pencil

How to cut a corner for a ceiling plinth

How to cut a corner? In order to begin installing ceiling plinths, you first need to know how to cut the corner of a ceiling plinth.

Angles are measured using protractors and a marking pencil, with which we can calculate which side of the corner we need to apply the piece on.

If we have a flat surface, we do this with a miter box at small angles, and then, using a stationery knife, we cut out the designated corners. If this plastic skirting board, you need to draw an approximate diagram in order not to make mistakes in the connections of the elements. Circumcision must be done carefully

How to cut a baseboard

In order to know how to cut the baseboard during installation, you need to have a miter box with you (for smooth surfaces) or a stationery knife, which is used for uneven corners.

If you have a plastic product, it is best to use a special hacksaw for metal, then cutting will be much easier.

It is necessary to trim the baseboards carefully, without pressing hard on the knife or saw, so as not to cut your hand instead of the corner of the baseboard. The miter box is used only for flat surfaces. The product is most often cut at small angles, at a distance of up to about 90 degrees. The stationery knife protrudes universal solution. When cutting, it is advisable to avoid places with cracks.

What is a miter box for ceiling plinth

A miter box for ceiling plinths is the most important tool for processing plinths in the ceiling.

It is distinguished by the presence of cutting tips on both sides at different angles from 45 to 90 degrees, which are located, as a rule, on the left and right sides. Using these tips, the plinth is clamped on both sides and sawed off cutting tool. In order to attach the parts of the plinth, you need to use a pencil to draw the necessary corners for joining. The marked product is inserted into the miter box so that it stands stably on its surface. The plinth is held with one hand, and with the other, from another angle, you need to cut the material.

How to glue ceiling plinth

In order to know how to glue ceiling plinths, you need to follow several rules:

1. always start from the corners of the room, they are the easiest, and then you can proceed to the rest of the room (you need to glue the corners so that no gaps form);
2. For plastic plinths, finishing putty is used for stucco moldings.

Places for fastening are moistened with soil or ordinary water.

After the putty has dried, it is recommended to seal the cracks on the surface. To seal them, sealants of various contents are used, but it is best to take the substance on acrylic base. For small room One package is enough. Installation with sealant is similar to putty.

More questions on your topic:

leave a comment

Builder's Dictionary:: Repair questions:: Calculators:: Special equipment:: Miscellaneous

2006 - 2017 © user agreement:: contact with the site administration [email protected]

Hello all readers! Today we’ll talk about how to properly glue a ceiling plinth with your own hands, quickly and without particularly straining. Having done this work, we will not only hide all the irregularities and joints of the materials with which the walls and ceiling of the room are finished, but also add some zest to the interior of the room.

Choosing a ceiling plinth

On the construction market you can find fillets made from materials such as:

• gypsum;
• tree;
• dense polymers;
• foamed polymers.

Flexible polyurethane skirting boards are ideal for installation in rooms with complex configurations, including those with round columns, semicircular projections or niches.

Other types of skirting boards are hard. The standard fillet length is 1300 or 2000 mm.

When purchasing a ceiling plinth, pay attention to its width and pattern.

Wide fillets are suitable for rooms with high ceilings(please note that if the plinth is large, you will not be able to use a miter box to accurately trim corners). And products with a pattern are much more difficult to join, since you will have to adjust the ornament very precisely.

The method of gluing it depends on the material of the plinth.

Gypsum elements are glued with putty, polymer skirting boards with “liquid nails” or other suitable construction adhesive, wooden fillets can be secured with self-tapping screws, but they can also be glued with a polymer adhesive.

Tools and materials

To carefully decorate the junction of the ceiling and walls with a plinth, you will need:

• tape measure, pencil, building level and sharp construction knife;
• miter box and hacksaw;
• putty + narrow spatula (for gypsum fillets) / “liquid nails” or other quick-drying polymer glue + mounting gun(for other types);
• masking tape and white sealant.

Preparatory stage

If you plan to cover the walls with wallpaper, it is better to do this after installing the ceiling plinth - firstly, the fillets will be more securely fastened, and secondly, the plinth will not have to be dismantled when the wallpaper is subsequently replaced.

Lightweight skirting boards made of foamed polymer can also be glued on top of wallpaper. To protect the wall finishing from accidental contamination with glue or sealant, apply masking tape around the perimeter of the room, leaving a distance from the ceiling equal to the width of the fillet.

If you want to make a colored ceiling edging, it is more convenient to use pre-painted skirting boards.

If you decide to paint the fillets yourself, check how the second layer of paint applies - whether you can subsequently unnoticeably paint over the joints between the elements filled with sealant or putty.

To calculate the amount of material, you need to calculate the perimeter of the room and divide it by the length of the selected fillet.

The resulting value is rounded up, plus one more fillet is added - a reserve for adjusting the elements and for accidental damage to the plinth during installation.

When purchasing, be sure to inspect each plinth - all elements must be from the same batch (so that there is not the slightest discrepancy in geometric dimensions and color).

Joining and cutting fillets

Gypsum and foam baseboards They are joined in straight sections with vertical cuts, and the seams are filled with putty/sealant.

If you are gluing polymer fillets, including painted ones, it is advisable to make oblique joining cuts at an angle of 45° using a miter box - then the joints will be almost invisible. They do not have to be puttyed or painted. It is also recommended to cut the ends of wooden fillets at an angle, or fill the vertical seams with pieces of veneer of the appropriate color.

The most difficult operation is joining elements in the corners.

It is from the inner corner that the baseboard sticker begins. If the corners of the room are relatively even, the profile is simply cut at 45°. The most convenient way to do this is to use a miter box.

Attention! If we are working with the right fillet, we insert it into the miter box on the right side; at the bottom there should be a part that will later be pressed to the ceiling. When working with the left fillet, it’s the other way around.

Don't confuse the direction of the cut!

If the angles in the room deviate greatly from 90°, you will have to make markings on the ceiling.

How to join the corners of a ceiling plinth: photo and video instructions

Press the plinth into place, resting its end against the wall, and draw a line along the ceiling. Then repeat the same operation on the adjacent side. From the point of intersection of the lines to the inner corner, draw a segment and measure at what angle you will have to file the fillets. This will have to be done by eye. To increase accuracy, make appropriate markings on your workbench and use them as a guide when cutting the baseboard.

Please note: for some types of ceiling plinths, corner rosettes are available that are suitable in size and design.

Their use simplifies the work, since you do not have to join the elements in the corners - the vertically cut ends of the fillets are inserted into the socket.

DIY baseboard sticker

Sticker for “liquid nails”.

Used for polymer and wooden skirting boards. Work progress:

• mark the bottom border (if the plinth is wide);
• insert the tube with the adhesive into the “skeleton” gun;
• Apply glue in continuous stripes to the back of the fillet - to the edges that will be in contact with the ceiling and wall;
• Press the fillet to the installation site and wipe off any exposed glue with a clean, dry cloth;
• Fill the gaps between the baseboard and the surface of the walls/ceiling with white sealant.

Putty sticker.

Suitable for plaster or other skirting boards, recommended for uneven walls. Work technology:

• using a level and a pencil, mark the lower boundary of the fillet installation;
• a thick working solution of finishing putty is mixed;
• putty is applied to the installation sites of the plinth and the top is treated with a primer;
• While the treated surfaces remain wet, apply a thick layer of putty to the baseboard and press it along its entire length to the wall and ceiling;
• remove excess working mixture with a spatula;
• After drying, fill the gaps between the elements, between the fillet and the surfaces of the ceiling/wall with putty.

Please note: heavy gypsum elements It is advisable to fix it on the wall with a self-tapping screw until the putty dries.

Sticking fastener subsequently removed, or its head is recessed, and the hole is covered with putty.

Video on the topic “Gypsum ceiling plinth - how to glue”:

Plastic Sheet Cutting Methods

Foundations are an essential part of any room's interior design, of course when it comes to living spaces. Although they are not uncommon, and in cases where there is no proper final conclusion, which is simply setting the base, even a strict service area seems incomplete.

The fact is that most floor coverings do not lie close to the walls, which leads to unsettled external seams, the concealment of which is the main task of knitted boards. Luckily, installation can be done easily with my own hands, the main thing is to figure out what needs to be cut into the plastic base, as well as how to repair it.

Choosing the Right Tool

The first and absolutely logical question that arises in every person who intends to install a pedestal is what to cut it out?

On the selected tool, you can directly determine how smooth the cutting edge will be. The fact is that PVC products have hollow structures, which makes using saw tools with large teeth or wide waves very discouraging as they can end up with tokens and numerous irregularities.

The teeth are quite small, and the width of the set is only allowed for PVC work. But here we can only use wafers because thin-walled spacers cannot withstand the impact of teeth, while the chip has an uneven appearance.

If you need to cut corners on ceiling tiles, you can easily do this using saw blades.

The result of the cut will be completely straight, no matter what plastic product we have discussed.

Of course, this tool also has a disadvantage - its small size, which will make it take a long time to work with large fabric material, and the use of a chair will be very unacceptable. I would like to point out that when stamping, it is strongly recommended not to use circular saw blades with abrasives, as they only complicate the entire process.

When it comes to panel thin wall panels, it can be cut with a regular office knife with a reinforced blade.

Of course, this version has its drawbacks.

For example, cleaning and even cutting can only be done if you have experience working with such tools and materials.

Slicing using mud

Proper pruning involves maintaining strict boundaries of geometric shapes.

This condition is mandatory to ensure good bonding between, for example, PVC panels and for wrapping blades.

How to cut ceiling coverings correctly

If you do it "with your own eyes", the results are unlikely to satisfy your quality, because one page does not match the other. This is especially important for the design of the outer and inner corners, so that a completely smooth cut is used that allows forty-five degree angles to be adjusted.

The tool is shaped like the letter “P”, in which the grooves are cutouts, the location of which corresponds to the selected cutting angle.

Each panel should have forty degree cuts so that when attached it reaches perfect angle in two planes in a room equal to ninety degrees.

Step by step for cutting drilling mud:

1. The tray in the center of the chair is used to secure the base into it.

   The panel must be applied to the device with a rough surface, since, on the other hand, the cut may damage the front. The above-mentioned diagonal slots are arranged so as to act as guides for the cutting part.

2. Then comes the step of selecting the desired angle. It is necessary to ensure that the edges of the panel do not extend beyond the edges of the guide slots. Only in this case can a reduction in quality be achieved. If the width of the cord being used is narrower than the tray on the chair, it is necessary to press the plate evenly onto one side of the slot and only in this cutting position.

   You cannot place the panel in the tray at any angle since the numbers will not be identical to each other later. PVC has a fairly elastic structure, so it is preferable not to press the pedestal while cutting because the cut is uneven. You cannot speed up the sampling process itself, as this will cause overheating and distortion of the edges.

3. After pressing one side of the corner you can move to the other, but with one difference - the other will be a mirror opposite the first.

   To cut through dirt accurately, there is a rectangular cutout that allows you to twist vertically rigidly.

Template template

If the angles on the walls don't match standard parameters, you can use templates.

To do this, strips of thin cardboard or heavy paper are used, from which strips are cut that correspond to the thickness in the selected base. They are applied to the corner joint and secured there, and then the unwanted part is cut with an office knife. The cutting should be perpendicular to the intersection of the walls, so that you can finally get two completely identical pieces of the same corner.

I hope my advice will help you master the repair and easily reduce the plastic lining.

Good luck in your efforts!

"How to cut a plate"

This detail concerns how to fix the base from below and how to connect the floor, ceiling panels in the outer or inner corner.

Installation of polyurethane ceiling sheet profiles

Installation of polyurethane profiles, also called ceiling panel, a little more complicated than installation regular design. All because polyurethane profiles are more difficult to install than sheet panels from ceiling posts. Therefore we will talk here about how to do the installation of polyurethane profiles and how they differ from gluing ceiling slab made of foamed polystyrene.

For tools you will need a chair (problems with the blade), a knife (for cutting burrs), a pencil, a pistol with liquid nails and color.

Despite the fact that the polyurethane structure does not require painting, i.e.

the surface is already painted, I advise the color in two layers, why, I will explain this further.

Once the polyurethane pattern has been painted in two coats and the color has dried, you can proceed with installation.

How to properly cut ceiling corners - detailed instructions

How to measure and write angles through dirt, I will not explain clearly enough. Liquid nails should be used often, but not too much, so they don't stick out over the design if you put it in the background.

When gluing it may move under its own weight, you can fix it with finishing nails.

After the design has been stuck in place for 2-3 hours, the nails are stretched and the nail locations and joints are mixed with paint and faux brush.

This is why you should paint on the design so that joints and cut corners are less noticeable, as well as nail marks

If you need to glue a structure onto a semi-circular surface, that is, a flexible polyurethane structure, it is different in color from simple polyurethane profiles, this is another reason to draw all the shapes after installation. The main thing is to ensure that the flexible bars are not cheap, with the same model as the regular ones.

When the design sticks together.

All joints should go through acrylic, remove excess and wipe with a damp sponge.
Video on how to fill cracks in a ceiling (design)

Often during repairs you may encounter a situation where it is necessary to saw off a piece from a part at an angle of strictly 45 degrees. Typically, this is needed to connect two parts at a right angle, 90 degrees, such as: door casing, baseboards, pieces of furniture and much more. Experienced master, professionally engaged repair work, can often do without special devices, and is able to cut the required part evenly and clearly by eye. But if you are a novice repairman, and you have a desire to do the job as efficiently as possible, without damaging expensive parts, then you simply need to purchase a special device that allows you to saw off material at a given angle without any special tricks.

To work, you need to have: a miter box, a hacksaw, a protractor with a pencil, a piece of wood, a screwdriver with screws or a clamp.

Using a ready-made miter box

The most common miter box is a U-shaped profile with slits on the sides, allowing you to use a hacksaw to make cuts at angles of 45, 60 and 90 degrees, respectively. It is enough to use it once and you will no longer have the question of how to cut at an angle of 45 degrees. There are miter boxes and more complex ones that allow you to independently set the angle required for cutting, and also, using a rotating structure, set hacksaw blade into the best position. The best option For a novice repairman, there will be a purchase of ready-made tools at any hardware store. The miter box can be made of wood, plastic or metal. But you can make it yourself from scrap material, any boards or plywood, about 20 millimeters thick.

Making your own miter box

1. 1. First you need to assemble the box of the future tool. To do this, it is necessary to drill holes in its side walls for future fastening with screws and, having smeared the ends of the parts with glue, connect them in such a way that both walls are strictly perpendicular to the bottom and parallel to each other, after which we fix them with screws.
2. 2. Using a protractor, mark a 45-degree angle with a pencil; if necessary, add additional lines for the grooves. The most important part is the cuts; they are best done with the same hacksaw blade that you will use to cut the products. It is necessary to saw while holding the blade, avoiding strong pressure on the tool; first saw through one side, then the other.
3. 3. Let's start processing the material. Using a clamp or screws, we attach the miter box to work surface. At the site of the future cut, we make a mark on the plinth or board. How to cut at an angle of 45 degrees becomes clear if you press it firmly against the side wall and align the mark with the slot on the template. We insert the hacksaw into the groove and cut the workpiece, while the work of the blade is limited to cuts, which allows you to make the cut as evenly and accurately as possible.
4. 4. Before sawing the baseboard, you need to make sure that the corner of the room is really straight and, if this is not the case, you need to adjust the cutting angle of the workpiece. To do this, measure the internal angle of the joint between the walls, and divide the result by two. If you do not have a professional rotary miter box capable of changing the cutting angle to the required value, then to achieve the result you need to cut additional grooves at the desired angle in a homemade miter box. This way you can cut the baseboard for the most accurate alignment.

Now you know how to cut a workpiece at an angle of 45 degrees. Perhaps it's time to move from theory to practical action... Stay tuned!

There are now more than enough tips on how to cut a baseboard at 45 degrees on the Internet, the only bad thing is that most of them are given by people who have never done this. Next, from a practical point of view, I will tell you how to cut skirting boards at the corners with your own hands in 3 options, and you will learn how to traditional ways, and about folk universal recipes.

The science of how to properly trim ceiling moldings in corners is not as complicated as it may seem.

A few words about tools and materials

Floor skirting boards are now made of wood or polyvinyl chloride (PVC), in other words, plastic. For ceiling fillets, the list is a little longer:

The range of ceiling plinths is much wider than that of the floor type.

1. Polyurethane - these skirting boards have good elasticity and can bend around radial and other curved surfaces, but in any case they need to be trimmed to precise angles;
2. Foam plastic - the simplest a budget option, the price of foam skirting boards is low and they are very easy to cut;
3. PVC - the principle is the same as for floor skirting boards, but the lineup much wider;
4. Wooden - similar to floor ones, only here there are also wide models;
5. Gypsum - with the advent of polyurethane and polystyrene foam, gypsum ceiling fillets faded into the background, firstly, they are heavy, and secondly, fragile. But to be fair, they are worth mentioning.

Since it is impossible to correctly cut the ceiling plinth and its floor counterpart without a good tool, we will dwell on this issue in a little more detail.

The best, almost ideal tool for trimming any skirting boards and more is a miter saw with a rotating bed. The high-speed disc makes smooth and precise cuts, and the bed in these units rotates to any angle. The only problem is the serious cost of this tool.

A miter saw is an almost ideal tool for cutting baseboards and more.

Considered one of the best hand tools for precise cutting of small bars - this is an abrasive saw. In principle, this is true, but I’ll tell you honestly, it’s not easy to find a really high-quality saw, even with the current assortment. If you decide to buy such a tool, then take a saw with a fine tooth.

Theoretically, foam and polyurethane can be cut with any sharp and durable knife. But at the same time you need to have a firm hand and at least a little experience in cutting foam. Plus, cutting wide fillets with a knife is very problematic.

Without experience, making a clear cut with a knife is very problematic.

Personally, if I don’t have a crosscut tool, I only use a hacksaw. It is suitable for cutting absolutely any material, from foam to wood. By the way, people often ask the question of how to cut a plastic baseboard for the floor, so take a hacksaw for metal and you definitely can’t go wrong.

For cutting skirting boards, a hacksaw is considered one of the best tools.

Three working methods for trimming skirting boards

For floor and ceiling skirting boards, the cutting instructions are almost the same. But if on the floor a crooked corner can be covered with something, then on the ceiling this is already a problem, so we will pay more attention to how to cut the ceiling plinths.

Method number 1. Classic miter box

The classic miter box is a U-shaped box with slots in the opposite sides. A piece of suitable size is inserted into this stock and sawed off with a hacksaw through the slots in the sides. The idea is not new, the tool is already several hundred years old, but despite its simplicity, not everyone knows how to correctly cut the corner of a ceiling plinth using such a miter box.

Not everyone knows how to cut a ceiling plinth in a corner using a classic miter box.

Tip: when trimming ceiling plinths, they are applied to the side of the miter box that is closer to you, and floor skirting boards on the contrary, you need to apply it to the side of the instrument farthest from you. This is not a dogma, but it is much easier to work this way.

It is easier to work with floor plinths, since the miter box lies on a horizontal plane, it is easier for you to orient yourself in the position of the plinth. People most often make mistakes when cutting ceiling fillets; they simply insert them into the tool incorrectly. There is a simple but important rule here.

Important: the side of the ceiling fillet that touches the wall should be directed to the upper edge of the side of the miter box, and that part of the plinth that borders the ceiling should be placed on the bottom of the miter box.

As you know, a corner has 2 sides, so in order to make fewer mistakes, train yourself to place the bar that will be mounted on the right side of the corner in the miter box on the right, and the bar that is attached to the left in the miter box on the left. The intricacies of using a classic miter box are described in detail in the video in this article.

In addition to the classic U-shaped miter box, there are two more types of similar designs - a professional and a rotary tool. Concerning professional version, then only masters use it. The device is quite bulky, but it rotates at any angle and has a hacksaw that can be locked in the desired position.

Professional miter box with the ability to fix a hacksaw and workpiece.

The rotating device can easily be called a “pocket” miter box. The only advantage here is the ability to clearly fix the angle of rotation of the bar. On the one hand, it’s easy to work with - set the corner, apply it to the baseboard and cut it off. But on the other hand, you need to get used to such a tool; if you do not have experience working with a hacksaw, then you should not take a rotary miter box.

Advice: when choosing a classic U-shaped miter box, first of all, do not buy Chinese products. And secondly, try to buy models with the ability to rigidly fix the part inside; one of these models is shown in the photo below.

A miter box with the ability to fix the part inside is much more convenient to work with.

Method number 2. Trimming according to a template

Most often, both ceiling and floor skirting boards need to be cut at 45º. If there is no specialized tool nearby, then an improvised miter box can be drawn on a piece of notebook paper. From the school geometry course we know that the diagonal of any square in relation to the base has an inclination angle of 45º.

Next you need to draw a square and draw 2 diagonals in it - this will be the required 45º. All you have to do is correctly attach the plinth to the leaf and mark. True, in order to cut the plinth smoothly without guides, you need a good eye and a steady hand.

Method No. 3. Applied universal

Trimming at 45º is a common option, but what if you need a different angle and only have a hacksaw and a pencil? It turns out that there is a very simple way out of this situation. Plus, this method is universal, it is suitable for both external and internal corners.

Moreover, I can assure you that those angles that visually seem straight, in fact have deviations of a couple of degrees. As a result, you buy good tool, you cut off exactly 45º, and when joining, a gap appears between the baseboards. Here this problem disappears. And then, using an example, we will look at how to cut the ceiling plinth in the inner corner.

Illustrations	Recommendations
	Stage 1. Take the fillet, place it on one side of the corner and use it to draw 2 lines, along the wall and along the ceiling. Advice: to make the lines unnoticeable, they can be drawn not with a pencil but, for example, with a nail or the tip of a knife.
	Stage 2. Do the same on the adjacent side of the corner.
	Stage 3. If you draw a diagonal from the intersection of the lines on the ceiling to the inner corner, you will get the desired cutting line.
	Stage 4. Next, take the tool and cut along the finished markings. If you are comfortable with a hacksaw, then the baseboards should fit together perfectly.
	. As I already mentioned, you can trim the outer corner using exactly the same technology.

Important nuances

If you tried your best, but a small gap at the joint still “came out,” do not be discouraged. In wooden fillets, such a gap can be easily covered with furniture wax. To fill a gap on baseboards made of polyurethane, foam, plastic or plaster, putty is perfect. Naturally, the color of the composition must match the color of the baseboard.

All cracks in the area of ​​the ceiling fillets are sealed with putty.

Wide ceiling fillets are certainly beautiful, but they can only be mounted on perfectly flat walls. If the plane of the wall in relation to the ceiling is wavy, then it is better to buy narrow polyurethane fillets, they are elastic and will smooth out this drawback.

The most questions arise about how to cut wallpaper to fit the ceiling plinth. There is nothing complicated here: the wallpaper is glued with a slight overlap on the baseboards and when the wall is completely glued, take a large spatula, place it in the corner and cut off the excess along the blade with a knife.

But keep in mind - neither the knife nor the spatula can be removed from the wall until you have gone through the entire plane. That is, you put a spatula from the corner, cut the wallpaper along the length of the blade, and then, without lifting the blade from the wall, move and cut until you reach the next corner.

Conclusion

All three methods I described work; the choice depends on what tool you have and what your professional skills are. If after watching the video you still have questions, welcome to the comments, I’ll help in any way I can.

If you are not confident in your abilities, then for both floor and ceiling plinths there are joining elements that allow you to do without trimming.