Repairing a glass table is not an easy procedure. The fact is that, due to its transparency, the glass table shows all the mistakes that you may make while working. For this reason, you must act very carefully. The most popular problem among owners of such a product is getting rid of scratches. In order to avoid this, you need to properly care for the table.
Glass table(option 1) Glass table (option 2) Glass table (option 3)
Glass table (option 4) Glass table (option 5) Glass table (option 6)
If you want to remove scratches and abrasions on glass, you cannot do without valuable advice. Scratches spoil appearance a product that had a neat appearance before this unpleasant incident.
1. Try it toothpaste 2. Try an ammonia solution
3. To remove deeper scratches 4. You can try jewelry polishing paste and pad
How to remove hated defects? First, prepare GOI paste. This special glue is sold in automotive stores. Pasta is sold by number. For glass products we will need the first or second number.
In order to get rid of cracks in glass, you need to grind the paste until it becomes crumbly. At the same time, it must be given homogeneity. Polish out any imperfections. In order to remove them, you need to dip a cotton swab into the crushed paste. You need to polish the scratches carefully, without pressing the stick. The procedure is repeated several times, and its duration is about ten seconds. Once polishing is complete, remove excess paste from the glass.
Repairing a wobbly table
Glue the legs
In order to repair a table leg that is wobbly, you need to understand the fasteners. The legs of the table were glued at the factory with a special glue, which may dry out over time. If the legs are secured with dowels, screws, screws, etc., they can simply be unscrewed and replaced. The legs can be glued if the tabletop is attached to them with adhesive bonds. In order to get to the damaged elements, the table is turned over in disassembled form. The screws are unscrewed from the tabletop itself. If a crack has formed on the leg under the tabletop, it can be glued. Place glue into the crack and cover it with a countertop.
If the glass tabletop is on a wooden frame
Glass table on wooden legs
We completely disassemble the base. We clean the old dowels from the old glue, apply new glue and put it in place.
We can secure the loose leg with a tie like this. Screw the pin into the leg and tighten the tie plate into place with self-tapping screws.
Connections can be strengthened metal elements. Give preference to the dowel. Insert one end of it into the cleaned hole, and sharpen the other so that it fits smoothly into the connection. Now you need to assemble the product. If you have never assembled it before, watch the video.
Glass table care
Taking care of a glass table
In order for the product to serve you as long as possible, it will need proper care. How to care for a glass table? First you need to figure out how to protect it from damage. If you cleaned the room, the table must be set. This will protect it from dust and possible damage. It is necessary to find a special approach to the glass table - wipe it with special compounds, protect it from exposure to direct sun rays and temperature changes.
If you have small children, a glass table could put their lives at risk. To prevent children from getting hurt or accidentally breaking the product, move the table away from children's games. It is best to install a glass table in places where it will be least exposed to household occupants. Pets are another risk to the existence of glass products. Fluffy fidgets can both break and scratch the table. For this reason, it is better to keep them away from the product. As you can see, if you properly treat a glass table, this piece of furniture can serve you for many years.
If you are tired of the old wooden tabletop, you can replace it with a glass one or make a glass table with your own hands. Many craftsmen are faced with the problem of attaching a new countertop. You will learn how to fix the glass on the table in this article.
What is a glass table cover?
There are two types of glass top tables:
- Many people purchase glass tables with a monolithic top.
- There are also transformable tables that can increase the length of the tabletop.
Important! This option is indispensable for a large family. In addition, it is ideal for a home holiday feast.
Such coatings are made from three types of glass:
- Tinted. This option attracts more attention from visitors to the home. Using this coating, you can highlight the interior of the room in which the piece of furniture is located.
Important! It will look very original if you add black chairs to a black glass table in the kitchen.
- Matte. IN in this case the glass takes on a slightly greenish color, as it is natural for such a material.
- Glass. In the interior of any room, such a design seems weightless and not as bulky as it actually is, and this adds a certain lightness and airiness to the room.
Pros and cons of the material
Before you move on to attaching the glass tabletop to the table, you need to understand all the advantages and disadvantages of the material you have chosen.
Let's start with the positive aspects:
- Original design. Glass tables make a very good impression and lift the mood of both residents and guests. This table looks especially great in a high-tech style interior.
- Resistance to external irritants. Many users are afraid to buy a countertop made of this material for fear that the glass may break. In fact, such a coating can be much stronger than wood.
- Moisture resistance and temperature resistance. Strained glass Do not be frightened by actively changing environmental conditions.
- Easy care. Such tables are very hygienic and easy to care for, including removing coloring and greasy substances, which is a definite plus. For the same reason, ordinary wooden kitchen tables are inferior to glass-topped tables.
Before you attach the glass to the table, think about it, because this surface also has some minor disadvantages:
- There are many stains and marks left on the surface. This problem can be solved by purchasing a matte countertop.
- Even the smallest dirt is visible. You have to remove all the stains with a liquid designed for cleaning glass.
- The coating can be easily scratched.
- Creates a lot of noise when paired with kitchen utensils.
- High price.
Let's move on to the attachment
Now is the time to get down to business. To do this you will have to follow this algorithm of actions:
- Make a hole at the ends of each leg.
- Attach suction cups to these holes using very strong glue.
Important! The adhesive composition used to attach the mirror surface will be visible through clear glass future table. In addition, such a composition takes a very long time to dry, which will be unacceptable for this work, unless, of course, there is an additional fastener on the leg.
- When adhesive composition When dry, use a felt-tip pen to mark the locations of the furniture legs on the tabletop.
- Degrease the marked areas using acetone or gasoline.
- Glue the glass tabletop to the legs of the table and wait for it to fully set.
- Irradiate until the adhesive completely polymerizes.
Important! It is necessary to take into account that it will not be possible to tear off the tabletop and re-attach the glass, so it is necessary to measure everything perfectly accurately.
Glass table top for kitchen table glued!
Exploitation
A glass tabletop needs to be handled very carefully. For this reason, it is necessary to follow a number of mandatory rules for caring for the surface:
- Wipe such a covering only with artificial suede or a microfiber cloth - these materials leave minimal amount divorces.
- To clean the coating use household chemicals, namely glass and mirror surface cleaners. This should be done approximately 1-2 times a week, as there is a risk of exposure to aggressive chemical compositions for food.
- You can easily get rid of scratches by sanding the surface with GOI paste, toothpaste or Polarit.
- To prevent scratches and chips, place special napkins on the table - they are quite easy to find in stores.
Video material
A table is a key element of the interior, and it doesn’t matter whether it’s a dining table or a coffee table. Tables with glass tops look especially interesting, because the interior takes on a completely the new kind, when such an element appears in it. From this article, you learned how to attach glass to a tabletop without glue, so that its remains do not spoil the final impression.
To glue glass to metal at home, you need to act very carefully and know several subtleties of the process, in particular, what exactly to glue. Glass is a delicate material, its properties affect how surfaces adhere to other matter.
When gluing, you need to pay attention not only to the use of good adhesion methods glass surface and metal, but maintaining the appearance of the product. Taking into account the product and the amount of work, they determine what can be used to glue the glass to the metal.
There are several types of glue for gluing:
- UV glue and UV lamp;
- Super glue;
- special adhesive type B 682-0, Verifix MV 750;
- epoxy adhesive;
- automobile;
- Moment;
- transparent silicone sealant.
Using UV Glue
Often in the process of renovating an apartment, when a glass product or piece of furniture breaks, a situation arises when you need to know how to glue the metal to the glass. One of the ways to correct the situation is 
A big part of the job is using an adhesive that contains a component such as methacrylic urethane resin. In addition, the work requires a special UV lamp, a degreasing compound and an industrial hair dryer.
In order for the parts to be glued to stick better, you need to polish and thoroughly treat the surfaces with a degreasing compound. What to replace it with? For these purposes, you can take regular alcohol. The next step is to heat the parts for gluing at the joining point a few degrees above room temperature.
Apply the adhesive and turn on the lamp for a few minutes. To apply the glue exactly to the right place, you can mark it with a marker. After hardening, the glue will become transparent and invisible at the attachment point. This must be taken into account if you need to glue not transparent glass, but frosted or colored glass.
The method of using UV glue and a lamp is considered expensive; its use is advisable if all components are present or there is a large gluing area.
Other types of glue for furniture repair
Superglue (cyanoacrylate) shows good results during repairs. It remains transparent after 
dries, sets in a few minutes and is easy to use. It's better to apply it thin layer, avoiding moisture.
For a strong and flexible connection, silicone sealant is used. You can also use car glue to repair the table. When dry, it acquires a black color and rubber properties. From the video you will learn how to glue glass to metal.
Bonding parts of kitchen appliances
Sometimes situations arise when you need to repair the oven door or microwave oven. If you decide to do this at home, the question arises: what glue should I use to glue the metal to the glass?
When choosing a connection agent, you need to pay attention to the following indicators:
- high degree of adhesion;
- elasticity;
- neutrality and exclusion of toxic emissions;
- heat resistance.
Specialized stores sell sealants for repairs. kitchen appliances or glue with silicone composition. For these purposes, you can purchase Dow Corning, but it is not available everywhere.
According to people who have encountered such a problem, there are other means that are no worse than imported ones, and in some ways better. Some suggest using an organosilicon compound based on rubber. This product does not emit toxic fumes and hardens without additional processing and withstands temperature changes. It is up to the consumer to decide which product to use.
To glue glass in the oven or hob, clean the joints and dry. Then apply glue to the metal according to the attached instructions. When repairing an oven, you have to carefully coat the metal joints, removing excess glue immediately, otherwise, after it hardens, it will be possible to remove smudges only with a special means.
Other craftsmen have found other ways to glue metal to glass:
- glue HC-1 and HC-2,
- glue BK-4,
- silicate glue,
- sealants for cars.
Auto glass
Car drivers often face the problem of replacing broken glass in their car. Of course, it is better to use the services of workshops, but every car owner should know the principle of replacement. 
To glue glass to metal, treat the gluing areas with a pneumatic knife, removing fragments and old glue. Clean and degrease the body at the junction. The glass is treated with some kind of activator and automotive glue is applied.
Gluing glass to metal yourself is not difficult if you use the appropriate types of glue for the job and follow the instructions. You can repair glass tables, ovens and other items at home.
