Wallpaper sticker has been and remains the cheapest and in a beautiful way wall decoration. Beginners can master it on their own; it is also used by masters with pleasure. This is a simple and easy process that takes little time. But, as in any repair work, you should have a minimum of knowledge and master some skills, without which the result obtained may upset a diligent worker. The question of how to properly paste wallpaper in the corners of a room has already initial stage work and requires careful preliminary preparation.
Preparing corners
Even if visually the corners seem even, upon closer examination the picture turns out to be not so rosy. The slightest irregularities on the walls and a crooked corner line will cause the canvas applied to the surface to lie crookedly on the adjacent wall and cause the wallpaper to rip and unsightly creases. The next strip of wallpaper, glued end-to-end, will not lie strictly vertically, the pattern will shift - as a result, the wallpaper will have to be torn off the wall and work started again. To prevent this from happening, you must:
Pasting corners, as well as the walls themselves, should not be done “by eye”.
In order not to rack your brains once again about how to glue wallpaper in the corners of a room, you need to prepare the tools:
- spatula (it should not be wide, optimal width-15cm);
- plumb line (allows you to maintain a strictly vertical level of the glued strips);
- construction knife (with its help, excess pieces of wallpaper are removed quickly and accurately);
- roulette;
- pencil;
- brush;
- roller;
- scissors.
A large number of wallpapers offered for sale have to be glued end-to-end, rather than overlapping, therefore, when deciding from which angle to glue the wallpaper, it is better to focus on strict vertical lines. Since perfectly even corners in modern premises practically never happens, you can start gluing wallpaper from the door or from the window.
How to cover an outer corner?
Before gluing wallpaper with a pattern in the corners, you need to prepare a canvas of such width that it goes around the edge of the outer corner and rests a few centimeters on the wall adjacent to it. To do this, you need to measure the distance from the edge of the previous strip to the corner and add 2-3 cm to the resulting value, transfer the measurements to the wallpaper, cut off the excess, and only then start gluing the corners. An edge that has been turned around a corner may cause creases. In these places, cuts are made with a construction knife. The canvas is carefully smoothed and pressed tightly against the wall.
Advice! When using heavy wallpaper(for example, vinyl) glue is applied both to the wall and to the wallpaper. To stick light (for example, non-woven) wallpaper, it is enough to grease only the wall. But in both cases, dried areas of walls and wallpaper need additional lubrication with glue.
A vertical line is drawn on the adjacent wall using a plumb line. The width of this section is determined from the corner and is equal to the width of the next panel with an addition of 0.6-1 cm. The second strip lies with its right side strictly along a vertically drawn line, and its left side overlaps the edge of the previous strip. It is necessary to carefully ensure that the motifs of the drawing on both canvases coincide. You must not only know how to glue wallpaper on the outer corner and use it skillfully, but also prevent the elements of the ornament from becoming chaotic. After the canvas is glued, you need to dip the brush in glue, coat the dried edges and press them tightly with a roller.
But, it’s one thing to figure out how to quickly stick wallpaper, another thing is to ensure that in the outer corners they don’t lift up or come off over time. It looks, to put it mildly, unaesthetic. To solve this problem, wallpaper corners are used. Long strips, reaching a length of 3 m, are quite easy to adjust to size. To do this, you can use a hacksaw. The next question arises: what is the correct way to wallpaper? They will not stick to wallpaper glue, and after use liquid nails Unsightly marks on the wallpaper cannot be avoided. Silicone sealant is ideal for these purposes.
How to cover an inner corner?
The work process is in full swing, and the vertical canvases lie flat on the wall, but the adjacent wall is getting closer and closer and you have to wonder: what does it take to hang wallpaper yourself in the inner corners? This is not as difficult as it seems at first glance, and certainly no more difficult than pasting external corners.
After the next strip is glued in front of the inner corner, you need to measure the distance from its edge on the right to the corner, add 1-2 cm to this value.
The dimensions are transferred to the next strip, it is carefully cut vertically (by eye). And for confident movement, use a spatula.
A canvas is placed on a wall carefully coated with glue. A strip of small width will also appear on the adjacent wall. You can get rid of creases using a construction knife. In the corner the canvas is very carefully pressed against the wall. A spatula is applied to the wall. The flat part is pressed against the wall and directed towards the corner. The construction knife follows the direction of the spatula. The narrow strip that ends up on the adjacent wall is carefully trimmed.
Advice! The dull parts of the construction knife must be broken off in a timely manner to avoid tears and inaccurate cutting of the wallpaper.
The part of the strip that was cut off can be used further. It is necessary to measure its width, subtract 1-2 cm from this value, transfer the dimensions to the wall, draw a vertical line. The ideally flat side of the wallpaper should lie strictly along a vertical line, and its left edge will overlap the previous strip. Using a sharp blade of a construction knife, carefully trim off the excess, as in the previous stage of work.
If novice craftsmen, when thinking about how to glue wallpaper in the corners of a room, begin to worry and rack their brains, then people who have mastered a simple technique with any wallpaper - be it heavy vinyl or light non-woven - cope with the same ease and speed. You only have to do the job correctly once, and then it starts to go wrong.
Pasting wallpaper on a straight wall is not difficult even for an inexperienced person. But the quality of the repair is determined by the ideal passage of corners, and it is this stage of work that is considered the most difficult. How to glue wallpaper in corners? There is a simple way to stick wallpaper in the inner and outer corners the way repairmen do it.
It is known that before starting work it is necessary to prepare the surface of the walls, and the corners require special attention in this matter. Irregularities should be removed by thorough puttying. After the putty has dried, it should be sanded with sandpaper. The surface must be perfectly smooth, otherwise the canvas will come off. The following rule is observed over the entire area of the walls: before starting work, they must be treated with a primer. You should wait for it to dry completely.
Internal corners: features of wallpapering
The canvas is glued to the wall so that it turns the corner by 5 cm. It is important to observe exactly this amount of rotation, since a well-chosen allowance allows you to properly wallpaper the corners. If it is larger, the strip will begin to “wrinkle”, and then you will have to make transverse cuts to smooth out the excess. If the allowance is smaller, the likelihood of it peeling off after drying increases.
The turn and inner fold should be smeared with glue especially carefully and the canvas should be pressed down well to securely fix it. Next, on the second wall, adjacent to the previous one, the width of the canvas is measured with a ruler. Standardly it is 53 cm; for non-woven wallpaper the roll width is 1 m. The mark on the allowance of the previous strip is fixed at a distance of about 2 cm from the corner. Then a vertical line is drawn through this mark, which is determined using a plumb line. This line is the edge of the canvas, which is glued first on the other side.
At the next stage of work, two layers of wallpaper are cut through. To do this, apply a long ruler to them, along which they draw with a sharp wallpaper knife. The top layer of the segments is easily removed or falls off on its own. Raises to remove lower sections top layer wallpaper, then it is additionally coated with glue and pressed against the wall. Thus, a perfect joining seam should be obtained.
This method can be used for any type of wallpaper.
Video example of pruning.
External corners: how to rotate the canvas?
The outer ledge must be perfectly smooth. If its edge has chips or unevenness, they need to be puttied. The work is carried out with a metal spatula, outside corner must be level and strictly vertical. If these conditions are met, the canvas is wrapped behind it. The edge of the strip is checked with a level, since it determines correct location the following paintings.
The second gluing method is carried out similarly to gluing in the inner corners. The strip is wound around the corner by 5 cm, the next one is glued overlapping this allowance. Then, under the ruler in the middle of the overlay, a vertical cut is made in two layers of wallpaper. It is important that the ruler does not move while working with the wallpaper knife, otherwise the cut may go to the side. That is why it should be metal, as it has greater rigidity than plastic.
These methods of processing corners are suitable for wallpaper that is glued end-to-end. They do not shrink after drying, so the seam will not come apart and the wall will not be visible. However paper wallpaper require compliance with the technological overlay 0.5 cm wide, as they shrink along the width. In this case, using a plumb line, the strict verticality of the folded edge is controlled. If it lies on the wall incorrectly, you should draw a line and cut off the excess. The next strip is overlapped by 0.5 cm.
Non-woven wallpaper is an excellent finishing option building material, combining practicality, convenience and beauty. In the process of sticking such wallpaper special attention You should pay attention to how to glue non-woven wallpaper in the corners evenly. Pasting with such material has a number of features that must be taken into account when working. For example, in order to glue non-woven decorations, a special glue based on non-woven material is used. Also, non-woven wallpaper does not require applying glue to the canvas itself, in addition, this type finishing material does not shrink during operation. Basically, they are glued end-to-end (with the exception of external ones).
Scheme for gluing wallpaper in the corners.
Tools and materials
So, in order to glue non-woven decorations, you need the following tools and materials:
- non-woven wallpaper;
- special glue;
- construction tape;
- building level;
- a simple pencil;
- metal spatula 350 mm;
- metal spatula 150 mm;
- stitching roller;
- containers for preparing glue and solutions;
- cutting knife;
- roller or brush for applying glue;
- plastic spatula.
How to glue inner corners with non-woven wallpaper?
Sequence diagram for gluing non-woven wallpaper.
It should be noted that there is one optimal and correct method that tells you how to glue the corners with non-woven wallpaper. Before pasting, the walls of the inner corner must be properly prepared: the old coating is removed, plastering work(if necessary), the walls are leveled, a primer is applied, etc. The adhesive must be prepared according to the instructions immediately before use.
In addition, the wall must be marked: using building level from the rib internal joint a straight vertical line is marked at a distance equal to the width with a deduction of 1-1.5 cm. If the pasting does not start from the edge of the internal joint, then the canvas is cut off, the width of which is equal to the distance from the joint to the edge with the addition of 1-1.5 cm. It should be noted that the best option is a method in which each side of the inner corner is covered with a separate panel. To do this, apply glue with a roller to the marked part of the wall. The application area must correspond to the area of the canvas that will be glued.
You should also additionally apply another layer of glue with a brush along the edge itself, along the upper border of the wall and below, directly at the baseboard.
The prepared canvas (with an allowance of 1-2 cm along the length) is applied, starting from the top, to the wall treated with glue, and ironed with a construction spatula in the direction from top to bottom and from the center to the edges. In this way, excess is removed. In this case, the left or right edge of the canvas (depending on which side is pasted over) coincides with the previously drawn marking line. Excess is removed in the following way: starting from the top, close to the pasted wall, apply a metal spatula 350 mm long (for smooth walls) or 150 mm long (for uneven walls), then the excess is removed with a cutting knife, while the knife blade moves along the metal plane of the spatula.
It should be noted that the blade of the cutting knife must be sharp to avoid defects when removing residues. The second part of the internal joint is glued in a similar manner. As a result, a joint of panels is obtained along the edge. Of course, if the reference point for pasting is not a corner, but another landmark, then it is possible to paste a part of the canvas of the appropriate width with a deduction of 1-1.5 cm.
Trimming the excess is done using a knife and spatula.
After gluing, joints on a horizontal surface are processed with a rolling roller.
How to glue external corners with non-woven wallpaper?
To paste the outer corners, all the above preparatory operations are carried out: leveling the walls, preparing glue, etc. It is preferable that there is a whole canvas on the outer corner. This gluing option is suitable specifically for smooth external joints, which must be glued taking into account the selection of the pattern.
If the whole canvas cannot be glued during the process of pasting the room, then the outer corner is pasted over with wallpaper so that the overlap is 1.5-2 cm. The other side is pasted over with the whole canvas, while the edge of the panel is glued to the edge. This option is most preferable if the material is intended for painting, which will hide defects in the pasting. However, this option is not suitable for wallpaper that needs to be glued taking into account the selection of the pattern.
Today, the most popular way to decorate walls is wallpapering. As it might seem at first glance to a novice master, step by step instructions is simple, which is why many apartment owners decide to stick wallpaper on their own, without knowing the specifics of the work. As a result, the fit of the paintings is incorrect, unevenness and other defects are noticeable, which shorten the life of the finish.
If the house has smooth, properly prepared walls without defects, it’s really not difficult to start gluing wallpaper. But few people know how to properly glue wallpaper in the corners, following the pattern, so that it looks beautiful and neat. In this case, you need to know about the techniques, without the use of which you should not start gluing wallpaper.
Next we will talk about in different ways How to properly glue wallpaper in the corners of a room, we will provide video and photo lessons that will help you save and complete beautiful design kitchen, corridor or hall independently.
What problems might you encounter?
Ideally, in order not to cut the strip at the joint, the corner in the room should be perfectly straight and vertical. In this case, gluing the wallpaper will not be difficult; all work will be reduced to a continuous operation, which consists of treating the wallpaper and walls with glue and fixing the canvas.
But it's perfect to brag even corners Not everyone can fit into their home, so at least one corner will be uneven and cause difficulties. At the same time appearance the first wall covered will be vertical, and the junction of the canvases and the subsequent transition to another surface will become increasingly distorted. This will make subsequent selection of the pattern impossible.
Preparing corners
If the corners seem absolutely even, before gluing the wallpaper, it is enough to go over them with fine-grained sandpaper or a thick, hard cloth to remove barely noticeable defects and remove debris and dust.
But, if the corners are noticeably crooked, have protrusions, or, conversely, cracks and niches, they must be leveled with putty. If the damage is very large (for example, there are pieces of the wall falling out), it is appropriate to use plastic corners.
Take note! Before pasting wallpaper, consider the following features:
- no need to cover the corners with a whole sheet of wallpaper;
- Do not glue wallpaper end-to-end in the corners.
If you glue the corners end-to-end, you will not be able to avoid unsightly cracks. Also, unevenly laid wallpaper in a corner will distort the entire picture and the overall vertical. The best option– wallpapering with an overlap, but please note that too wide an overlap is unacceptable, its optimal width should not exceed 1-1.5 centimeters.
Features of work depending on the type of wallpaper
An equally important point that needs to be taken into account before starting to paste the walls is the material from which the canvas is made, because different material requires a different approach to work. How the type of finishing material affects the technology of forming corners, see the table below.
| Type of wallpaper |
Features of the work |
|---|---|
| Paper | A paper roll of wallpaper, which does not have complex additives, is the most demanding. You need to work with such wallpaper as quickly as possible so that the material does not absorb excessive amounts of moisture from the glue. If you overexpose the panel treated with glue, you risk that it will fall apart in your hands onto the lapti. |
| Vinyl | How to glue meter-long vinyl wallpaper on a non-woven base in the corners depends on many details. Before applying glue-treated wallpaper to the wall, you need to give it time to soak. Please note that some varieties vinyl wallpaper can be coated with a gentle coating, which can only be worked with a roller with a rubber working surface. Since this material is very heavy, the corners must be carefully opened with glue to ensure sufficient adhesion of the material to the wall. |
| Non-woven | How to glue non-woven wallpaper in the corners, and generally on the wall, is slightly different from working with paper varieties. They do not need to be treated with glue, just coat the wall. In order to secure the edge of such a canvas well, just before forming the overlap in the corner, the wallpaper must be additionally coated with glue. |
Please note that the thicker the wallpaper is used, the smaller the overlap needs to be.
How to glue wallpaper in corners (video)
Wallpapering the inner corners
The goal of high-quality wallpapering is to ensure that “wrinkles” do not form during the work, and that there is no gap between the panels towards the baseboard. To achieve this, you need to install a strip of wallpaper so that the grip on the adjacent wall does not exceed 2cm. To do this, it is important to take into account how strongly the angle is curved, because the greater the deviation from the norm, the larger the allowance needs to be formed.
It is very important to press the wallpaper against the wall as firmly as possible. If this causes “wrinkles” to form, they can be reduced slightly (sometimes even completely removed) by cutting the wallpaper in the direction of the formed wave. Since the beginning has been made, now it’s time to apply the markings, following which the second strip will be laid. To do this, it is necessary to set aside the width of the wallpaper, reduced by 5 mm, from the overlap of the first strip, which was launched onto the adjacent wall. Then you need to put the vertical aside with a level and glue the second strip.
How to design external corners?
To form an outer corner, you need to mark a point that will be the start of the sheet of wallpaper so that it goes around the corner by 3cm. The edge of the panel must be carefully fixed to the wall, and if “wrinkles” form, you can remove them, as we described above in the article.
Along the edge of the canvas that is laid on the adjacent wall, tear off a thin strip of wallpaper so that there is a small edge left. Such actions will remove excess volume from the seam, making the overlap less noticeable. Then, using a level, you need to set aside the distance from the corner, which is the width of the wallpaper sheet, plus 6mm. Along this line, you can glue the next strip of wallpaper so that the edge of the new canvas overlaps the edge previously placed on the wall. Applying force and pressing the joint tightly, trim the wallpaper and treat the joint with a rubber roller.
Photo gallery of finished works
If you decide to renovate, be prepared for complex process, which will take a lot of time and effort. And turning to professionals will also be costly in terms of finances. Therefore, in order to save your money, we suggest doing at least part of the work yourself. For example, you can easily cope with such a process as wallpapering walls. The only difficulty you will have to face is the design of the corners of the room. As a rule, this work always causes difficulties.
Unfortunately, both apartment owners in old buildings and new buildings encounter uneven corners. Often there are defects on the walls that prevent you from hanging wallpaper beautifully and quickly. What to do in such a difficult situation and how to glue wallpaper in the corners? Below you will learn about all important points, and for clarity you can watch the video.
Pasting corners: featuresIf you are gluing external corner protrusions, make sure that the wallpaper fits tightly to the wall, so it is not recommended to glue the entire strip to the corner at once.
If the joint of the walls is bad, it will simply gather in ugly folds. Moreover, the wallpaper should never end in a corner. It is necessary to leave an overhang of approximately 3 cm (if necessary, trim it with a knife). This way you can achieve a perfectly even pasting. When using thick wallpaper to decorate walls, use a plumb line.
If there are switches or sockets nearby, remove their covers and turn off the electricity. Next, glue the canvas on top, then cut out circles of smaller diameter than the casing itself. When finished you can put them back.
Preliminary preparation
It’s worth noting right away that all the preparation needs to be done long before gluing the wallpaper in the corners. First you need to remove old finishing, level the surface. To align wall joints, use plastic corners, securing them with putty.
Then the surface is treated with a primer, which can be found in every hardware store. The primer is applied with a roller or brush.
How to glue wallpaper in corners: technology
You cannot cover all corners at once. Choose the one from which the work begins. To do this, prepare a strip required length and depending on the type of wallpaper, coat adhesive composition both one wall (in the case of non-woven wallpaper) and the wallpaper (in the case of vinyl wallpaper). If you use plastic corners, you need to coat them with glue.
When processing the wall surface, it is necessary to cover an area slightly wider than the wallpaper (minimum 5 cm).
Then you can start gluing the first canvas. If you are going to start pasting from left to right, you need to apply it to the corner left side canvases. The strip of wallpaper is located exactly along its entire length.
Then the canvas must be carefully leveled and all the air expelled from it. This can be done using a plastic spatula or a special roller. After this, the entire wall is covered up to the next corner.
Internal corners
Internal corners are most common in rooms. To properly paste them, you must adhere to these recommendations.
The strip must be glued so as to cover not just the corner itself, but also several centimeters adjacent wall. Next, it is important to press and smooth the wallpaper well using a lint-free cloth or sponge.
Then, using a ruler or tape measure, measure the width of the wallpaper on the adjacent wall from the top corner, turning it back 3-4 cm. This is necessary so that you can glue the strip overlapping the previous one. Further along these points, using a plumb line or level, you need to draw a line along the wall. The canvas glued to it will be strictly vertical.
Next you need to start gluing the adjacent wall. As noted above, the canvas is glued overlapping the previous one along the drawn line. Next steps traditional: a strip of wallpaper is smoothed and pressed. Using a level, ruler or paint knife, cut through both layers of wallpaper in the corner, removing all scraps. It is important to do this especially carefully. If it is difficult to pry off the edge of the wallpaper, you can carefully bend the second sheet, removing all excess. After this, coat the folded canvas with glue, pressing it well and smoothing it, getting rid of air.By resorting to this technology for gluing the inner corners of the room, you can make the joint in these places invisible.
External corners
Found in almost every room external corners(slopes). For easy and high-quality gluing, it is necessary to pre-level them using plaster. But this will not always be possible. In this case, without overlapping pasting, you will not be able to achieve the desired result. Let's look at how to wallpaper the outer corners in more detail.
First, you need to glue the wallpaper so as to cover 3-4 centimeters of the adjacent wall. Moreover, it is important that the wallpaper fits evenly and tightly to the wall and corner. For this reason, if necessary, prune them in several places.
After smoothing the canvas, trim off any excess wallpaper (vertically) using sharp blade or a knife, leaving a thin edge.
Then measure the width of the roll with a large ruler or tape measure and, stepping back about 5 mm, draw a vertical line using a plumb line or level. The next strip is glued along it. It will lie flat. As a result, you will end up with a slight overlap. It will hide all defects that arise after cutting the first strip.
Features of gluing wallpaper with a pattern
If your wallpaper has a pattern that has good clarity (for example, some geometric shapes and shapes, vertical or horizontal stripes), you need to make sure that wallpapering in the corners does not distort it in any way.
This can be done easily. It is only important not to forget about the need to make a slight overlap on the wall. The canvas must be glued so that the edge lies exactly plumb. Then trim the second edge of the canvas along the edge of the corners.Most likely, you will not be able to completely eliminate the pattern shift, which will result in a slight distortion remaining. But only you know about this drawback. To identify it, you need to carefully examine the connecting lines of the walls. If you strictly follow the instructions on how to properly glue wallpaper, the canvases will lie exactly vertically, and minor distortions of the pattern will be unnoticeable.
How to glue wallpaper in the corners of a room: some secrets
- If your wallpaper is heavy and thick, it would be a good idea to arm yourself with strong adhesive. It will be good if it is transparent.
Sticking to our simple tips You will wallpaper the corners of the room perfectly. Moreover, they will look beautiful, even uneven wall joints. You just need to be patient and do all the work carefully.
