Adjusting plastic doors for the winter. Adjusting plastic balcony doors yourself with video instructions

Adjustment of plastic doors is extremely rarely required, provided that such structures were correctly installed from the beginning. In most cases, the need for adjustment is due to the formation of a natural imbalance in their mechanisms during long-term operation.

Plastic doors – what to check after installation?

Experts recommend ordering plastic (PVC) structures exclusively from those manufacturers who have positive reviews from consumers and recognizable in the market building materials. Poor quality products even with the most careful attitude They will break down very quickly and cause you a lot of trouble. They will have to be constantly repaired and, in the end, new designs will still be purchased.

Also special attention You should pay attention to the installation process of purchased doors. Master installers must perform the correct initial adjustment of the structure installed between rooms, at the entrance, on the balcony. When receiving the installed door, check:

1. Fit tightness door frame and the frame of the installed structure. If the product fits like a glove, then everything was done correctly. The fit must be uniform and tight in all areas of contact.
2. Vertical installation accuracy. The door must open and close without any significant physical effort on the part of the user.
3. Presence of drafts. Open the structure halfway, wait a couple of minutes. In situations where the door closes or swings open spontaneously, we are talking about improper installation. Require proper adjustment of the product.

Common causes of problems with PVC structures

Customizing plastic doors on our own allows you to troubleshoot major problems. The latter usually arise due to the fact that the moving components of the products we are interested in get confused during operation. This leads to a change in the location of the PVC construction leaf in relation to the door frame. Frequent problems with plastic doors are caused by the following phenomena. Firstly, by rubbing the canvas in the area of the handle or slightly above this area. A similar problem arises due to temperature deformations. This is especially common when using balcony and entrance doors.

Secondly, by rubbing the canvas along the threshold (that is, below). Many consumers believe that this phenomenon is due to the low quality of the product. But this is not true. It’s just that during installation the adjusting screws of the mechanism were not tightened completely or not tightly enough. Rubbing also often occurs when the door is heavy (for example, if you installed heavy double-glazed windows on it). Excessive weight causes the structure to sag.

Thirdly, due to the loss door block tightness. The problem is caused by an insufficiently tight fit of the structure to the frame or a change in the position of the special roller included in the door structure. The problems described are easy to solve on your own, without calling specialists and paying for their far-from-cheap services. In addition, the PVC door on the balcony, the entrance to the house, between its individual rooms can be adjusted on your own and if there are other difficulties with its operation. More on this later.

When to make immediate adjustments

Adjustment of balcony doors and plastic doors installed at the entrance to the building is carried out immediately if they allow cold air to pass through when closed, as well as in the following cases:

opening the product requires significant physical effort;
the door does not stay closed when the locking mechanism is open;
the lock handle is loose or very difficult to turn;
the design clings to the box when slamming shut.

These phenomena indicate that the door needs to be adjusted urgently. If you do not do this right away, after a short period of time you will not be able to use it fully. And then you will not have to regulate the structure, but carry out a full repair of it, which will require serious financial costs. In some cases, neglected doors have to be replaced with new ones. Also, adjustment of a plastic balcony door is also necessary in case of implicit violations in its functionality.

Experts advise checking the condition of the structure yourself once every 6–12 months using simple techniques. Take regular sheet from a school notebook. Place it in the middle of the threshold and close the door. The piece of paper should be tightly clamped with the canvas. After this, pull the paper out from under the door and pay attention to the force applied to perform this operation. Then place the sheet under the other part of the opening. Pull it out again and so on. If the applied force is the same in all areas, there is nothing to worry about. The structure is in in good condition. If in one area the leaf is pulled out easily, and in another with great difficulty, it means that the position of the door in relation to the frame has changed. PVC product customization required.

The second verification method is a little more complicated. We need to arm ourselves with a simple pencil and stand in front of the door on the side opposite to the direction it opens. Then you close the structure and outline its perimeter along the edge of the box using a pencil. Open the door and look at the resulting lines. In cases where they are strictly parallel to the edges of the canvas, everything is fine. If there is no parallelism, you need to figure out how to adjust the plastic door and begin this operation.

Regardless of the test results, be sure to adjust the structure’s pressure after winter, as well as before the onset of cold weather. In the spring, you should slightly loosen the clamping mechanism, and in the fall, strengthen it. Then the elements of the block will wear out noticeably slower, which will increase the period of trouble-free operation plastic product.

Adjustment options – horizontal and vertical

Plastic structures are adjustable in horizontal, frontal and vertical directions. All operations are performed using simple devices and working tools. Stock up on pliers, screwdrivers (flat and Phillips), tape measure, PVC gaskets, hexagons (it is advisable to have a full set of such keys with various types profiles).

Adjusting plastic entrance and other types of doors horizontally makes it possible to select the size of the gap between the hinge support and the leaf. A special element - a screw - is responsible for opening to the left or right. It is usually hidden under a special cover that covers the adjustment part we need. When, when closing, the PVC door rubs against the frame (along its entire height or only in the middle part) from the side where the locking mechanism is installed, the problem is solved simply. Do-it-yourself lifting of a balcony door is done as follows:

Open the plastic structure, use a 3 mm hexagon to unscrew the screws from all the hinges. You get access to decorative elements.
Remove the covers (you need to slam the door before doing this).
You can see the adjusting screws in front of you. Turn them clockwise (number of turns – 1–2). It is necessary to turn the screws on all hinges the same number of turns!
If the door sagging is noted only in the lower left or right corner of the door leaf, only the middle and upper hinges should be tightened. You don't need to touch the bottom one.

The vertical setting allows you to choose optimal height suspension plastic construction in relation to the box. This adjustment is carried out when it is necessary to lower or raise the entire door. The operation is performed using screws that are located at the ends of the (lower) hinges. The adjusting parts are directed along the axis of the latter. On entrance doors made of PVC, as a rule, the screws are closed with a plug. It needs to be dismantled. The screws rotate with a 5 mm hexagon. When turning the adjusting part clockwise, the door structure moves up, counterclockwise - down.

To adjust the strikers (elements located at the bottom and top of the box), use a 2.5 mm hex key. But in in this case You will also have to use screwdrivers. They make it possible to move the locking bars.

We adjust the position of the clamp using different parts

Front adjustment is used when it is necessary to adjust the pressure. This procedure is carried out in different ways depending on the design features of the plastic product. Pressure adjustment can be made:

1. Eccentrics. They are mounted at the end of the canvas (in relation to the hinges - on the opposite side). It is necessary to turn the eccentrics to ensure the required pressure.
2. Trunnion. This part is on door fittings. The trunnion is adjusted with pliers. If it is necessary to loosen the clamp, it is turned strictly parallel to the plane of the door. Use pliers carefully to avoid damaging the part. To increase the pressure, the trunnion is turned perpendicularly.
3. Striker. Under it there is a hexagon screw of a certain profile. You need to move the bar and work some magic with the adjusting element. Check the clamping level after each turn of the screw.

With prolonged use of plastic doors, their adjustment using screws becomes more and more difficult each time. At one point you will see that the adjusting parts are installed in extreme positions. There is simply nowhere to rotate them. In such situations, try adjusting the door using plastic spacers.

Using a regular chisel, carefully pry the glazing beads that secure the glass unit into door product. Dismantle them. Using small spatulas (sold in hardware stores), insert PVC gaskets between the leaf and the glass unit, thereby changing the geometry of the door. Let us say right away that it is difficult to carry out such a procedure on your own. It is necessary to select the thickness of the gaskets down to the millimeter and, in addition, know the exact place where they need to be mounted. Be sure to mark the dismantled glazing beads. They need to be put back in the same places where they were. When installing glazing beads, use a rubberized hammer. This tool will allow you to carefully tap the fasteners.

Replacing the seal and adjusting the handle - do it correctly

If door design If used for a long time with distortion, this is guaranteed to lead to deformation of the seal. Instructions for replacing the latter are given below:

1. Purchase a new seal. Pay attention to the shape of its section. It must be similar to the previously used product.
2. Use a screwdriver to remove the failed seal.
3. Clean the vacated groove from any remaining adhesive and dirt. Treat it with glue.
4. Install a new sealing product. It should fit into the groove freely, without the slightest stretch.

PVC door handles often become loose during operation. They may also not turn completely or may be very tight. We can deal with loose handles without any difficulty. Remove the cover that covers the area where the locking mechanism is secured to the door leaf. You will see two fasteners in front of you (usually screws). They should be slightly tightened with a Phillips screwdriver. After this operation, the pen will work flawlessly again.

Other defects in the locking device in most cases occur due to door distortions. As a rule, after adjusting the blade using the methods we discussed above, the handle begins to function normally. If adjusting the PVC structure does not solve the problem with constipation (it still doesn’t close well), you will have to change it.

How to prevent problems with plastic doors

If you want to adjust PVC structures as little as possible, pay special attention to the fittings installed on the door. The mechanisms of the latter should easily withstand loads of up to 120–130 kg. Then you won’t have to think for a very long time about how to tighten the door or figure out why it doesn’t close well. Cheap fittings (in particular, Chinese ones) are not designed for the specified loads. Its strength limit is 80–90 kg. Naturally, it fails quite quickly.

Besides, great value For trouble-free operation of plastic doors, it has two important options - an opening limiter and a microlift. PVC structures are not initially equipped with these devices. They must be ordered separately before installing the plastic product. The opening limiter is a kind of tire. It takes on part of the weight of the door. This significantly reduces the risk of sagging of the plastic sheet. With proper initial adjustment, the limiter eliminates the possibility of the door hitting the slopes, due to which the trouble-free operation of the fittings increases by 2–5 times.

It is recommended to install a microlift on heavy doors (entrance, balcony) equipped with double-glazed windows with two chambers. This device prevents sagging of the canvas when closed. A microlift, in its essence, is an additional supporting element that takes on part of the load. Structurally, it is made in the form of a roller or a movable plate. They are mounted at the bottom of the door leaf or at its end.

Evgeniy Sedov

When your hands grow from the right place, life is more fun :)

Content

Installing PVC structures with double-glazed windows makes your home more comfortable and warmer. However, often happy owners of balcony groups are faced with the need to regulate them. If problems arise in the mechanism, you can fix them yourself by following the instructions.

When does a balcony door need to be adjusted?

As the PVC structure is used, the following problems may arise, indicating the need for its repair:

cracks in the glass unit;
opening is difficult and requires excessive effort;
the canvas touches the box when closing;
the plastic balcony door creaks;
the system does not stay in closed position, if it is not locked;
the penetration of cold air from the street is noticeable when the door fits tightly to the frame.

The problems may not be so obvious. How to check:

To determine exactly whether adjustment is needed, take plain paper and place it on the frame.
Then close the canvas and pull the sheet towards you.
Do this around the entire perimeter, and observe what efforts are made to pull out the paper.
If in some place the sheet is pulled out easily, the canvas does not close tightly and requires adjustment.

What to do if the balcony door does not close

The structure intended for the balcony is less stable compared to the entrance group and windows, and easily sags under the weight of the canvas. You should not wait until the mechanism completely ceases to perform its function and completely fails. If problems occur, adjustments are required. How to adjust a plastic balcony door? You can use the help of a specialist for free if the warranty period still lasts. Another option is self-tuning, in which savings on repair costs are obvious.

How to adjust plastic balcony doors

Correcting the operation of a PVC structure requires the availability of tools and means. Self-configuration allows you to inexpensively solve problems in the operation of the sash. Before adjusting the plastic balcony door, prepare:

a set of L-shaped hex keys (in most cases a size of 4 mm is required);
plastic linings:
pliers;
Phillips and wide blade screwdrivers.

How to adjust plastic doors on the balcony? First of all, it is necessary to establish the reasons leading to dysfunction. To do this, you can open the sash wide and carefully inspect the seal. Traces of compression on the cord indicate the nature of the displacement. An additional sign of deformation is a malfunctioning handle that turns with great effort or has limited travel.

Adjusting the plastic balcony door when sagging

The significant weight of the glass unit and frame leads to deformation of their position. How to raise the canvas if it has sagged? Your actions:

Open the sagging canvas wide open.
Unscrew the screw securing the decorative trim.
Close the sash.
Remove the caps.
Adjust the long horizontal screws in the hinges. For lifting bottom corner near the handle, adjustments are required at the top and in the middle. If you need to adjust the entire height, tighten three loops.

How to tighten a handle

Often profile elements become loose. If the housing is not damaged, you need to tighten the fasteners. How to adjust a door with a faulty handle? Your steps to resolve the problem:

Open the door.
Disassemble the base of the element by rotating the cover 90 degrees.
Carefully tighten the exposed screws with a screwdriver, being careful not to damage the housing.
Replace the cap.

How to eliminate interference in the middle of the frame

If the sash catches the frame in the center, you need to move it towards the hinges. This is mostly enough to solve the problem. If such actions are not effective, replacement of the fittings is necessary. How to adjust a plastic balcony door yourself and save on the cost of repairs? Your actions:

Tighten the screw on the side with an adjusting wrench to move the blade to the bottom loop. After this, the sash should be attracted.
Repeat the same at the top.

Before you adjust the plastic balcony door, you should get acquainted with useful recommendations. They will allow you to achieve a positive result.

Before adjusting the double-glazed balcony door, it is necessary to establish the cause of the malfunction. The following options may be available:

The lower end of the sash touches the threshold. This means that the plastic balcony door sagged under its own weight. The structure has an impressive mass, so as a result of constant physical impact, the fittings (especially the hinges) begin to deform.
The sash shuffles in the middle of the frame. Most often this is due to lateral displacement. It can be caused by temperature or physical deformation.
The balcony door does not close well and cracks appear. This is due to poor fixation of the sash with the seal.
The handle is wobbly and does not “sit” well in the grooves. In this case, the problem is solved by adjustment.

To ensure that adjusting the pressure of a plastic balcony door is required as little as possible, you need to follow some practical recommendations from experts.

Before purchasing, pay special attention to the choice of accessories. Its technical characteristics must fully correspond to the weight of the structure.

Advice: the lion's share modern mechanisms designed for a weight of 100-120 kg and this is enough in most cases. However, if you have a particularly heavy structure (for example, a 3-4 chamber double-glazed window, then you should purchase more powerful models).

Use a sag compensator (also called a microlift). This is a small and cheap mechanism that will prevent the sashes from sagging under their own weight. Its use is fully justified.
Adjusting the PVC double-glazed balcony door will be required much less often if you use an opening limiter.
When operating, avoid sudden movements or applying too much force. Often, problems with mechanisms arise precisely because they are not used very carefully.

Instructions for proper setup

In order to adjust the balcony door, you will need a set of hexagons. So let's consider various options settings.

Fixing problems with the handle

In most cases, there is only one problem - the handle itself has become loose in the grooves. It's very easy to fix and all you need is a standard Phillips screwdriver. You need to do the following:

Pick up the plastic cover with something sharp, for example, a knife.
Rotate it clockwise 90 degrees.
Tighten the existing bolts until they stop, but not too tightly.
Put the cover in place.

If this procedure did not help, and the play remained; most likely, the handle is faulty and needs to be replaced. To do this, just unscrew the bolts and pull out the handle and insert a new one in the same way.

Fighting bad pressure

To check whether configuration is required or not, you can follow a simple procedure:

We place a sheet of paper on the frame of the open sash.
We close it and try to stick out the sheet.
We carry out this procedure along the entire perimeter.
If it is pulled out with great difficulty, everything is in order. Otherwise, you will need to adjust the balcony door to the pressure, about which we’ll talk further.

So, the sequence of actions looks like this:

We examine general condition design (we pay special attention to the seal).
You also need to make sure that the handle closes all the way.
If there are problems with the door movement, they can be eliminated by adjusting the screws in the hinges (in most cases there are 3 of them).
Open the door wide, unscrew the screws and remove it from the hinges.
As a result, we will see a long screw located horizontally. It needs to be tightened and the structure returned to its place.
If the operation does not help, we tighten the eccentrics - these are mechanisms located at the end of the sash. They are responsible for the level of its pressure. They are usually hexagon shaped.

Correctly eliminating sagging

If the balcony adjustment plastic door is necessary due to its sagging, you will need to perform the following manipulations:

We open the door.

Please note: some hardware models will require an asterisk key.

Using a 4 mm hexagon, we turn the screw at the end of the door (usually it is located next to the top hinge). We make several turns clockwise.
We return the sash to its place (close it).
Remove the plastic covers from the lower hinges. This will allow you to get close to the adjustment screws.
Tighten the screw located on top. As a result, we will raise our sash, giving it the correct position.
We carefully check the progress. If problems are still observed, we repeat the operation until they are eradicated.

To ensure maximum comfortable operation, we recommend regularly lubricating hinges and other moving elements. Perfect for this universal remedy WD-40.

Solving the problem with grazing in the middle of the frame

This problem is much easier to fix. Our task is to move the sash closer to the hinges. This is done as follows:

We move the sash to the lower hinge. To do this, tighten the side adjusting screw. In the end, she should be attracted.
Repeat the procedure for the top loop.

In most cases, these manipulations are sufficient. If they do not solve the problem, the fittings will most likely need to be replaced.

Conclusion

Replace old wooden ones balcony blocks Almost everyone is now trying to get new plastic ones. After all, such structures are more attractive in appearance, do not lose this quality over time, and better protect the room from the penetration of cold or, conversely, hot air from the outside. However, even the most expensive PVC structures have an unpleasant feature: they require adjustment and adjustment of the pressure at some intervals. Let's find out on our own, without turning to specialists.

When do you need to adjust plastic balcony doors?

Adjustment of plastic doors to the balcony is carried out if the following disturbances in the operation of the mechanism are noticed:

effort must be made to open;
closing the doors on the balcony, you can feel how the canvas clings to the door frame;
the lock handle is loose or, on the contrary, it turns too hard;
if the lock is open, the door swings open spontaneously;
from under closed door blowing

The detection of these symptoms indicates a poor condition of the plastic structure and the need for adjustment. It is possible that simple adjustment will not help; some parts will need to be repaired or replaced, which entails extra costs. To avoid such a situation, we recommend that the doors on the balcony be adjusted regularly and in a timely manner. There are several simple ways to detect violations.

Methods for identifying the need for adjustment of plastic structures

You can check whether the door structure needs adjustment using simple steps.

Don't close completely door leaf. If it does not remain in its original state, but begins to open/close on its own, then it’s time to make adjustments.
Stand on the opposite side from the opening direction. Using a simple lead pencil, outline the edges of the door. Now open the balcony, take a closer look at your “drawing”, if the lines you drew are parallel to the edges of the door frame, there is nothing to worry about. Otherwise, it's time to get out the tools.
Hold a notebook or newspaper sheet against the balcony door and try to remove it. How much effort did you have to make? This manipulation should be repeated in different places. Everything is fine with the clamp and no adjustment is needed if the same effort was applied to pull out the sheet.

How to adjust plastic balcony doors?

Before you start adjusting the balcony doors with your own hands, make sure you have the following tool:

screwdrivers of different sizes, flat and Phillips;
pliers;
keys with different profiles;
measuring tape;
plastic gaskets with a self-adhesive layer;
erasable marker or pencil.

In some cases it may be necessary to have liquid plastic, solidifying on contact with air.

Directions for adjusting plastic doors

This process is carried out in several directions:

frontal;
horizontally;
vertically.

We invite you to consider each of them in more detail.

Horizontal adjustment

Temperature fluctuations can cause deformations, which make it difficult to close the doors; they begin to rest against the mechanism. Closing can only be accomplished with considerable effort. However, these actions are undesirable, because by doing so you provoke further deformation.

To adjust, you will need to tighten door hinges. This is done using an H4 hexagon.

Insert the tip of the screwdriver into the adjustable screw located on the side. Access to it is located on the lower side plane of the door hinge.
Pull the sash to the hinge by tightening the screw.

This way you will be able to move the sash 1 cm to the right or left. If necessary, a similar adjustment is made with the top hinge. After this, the closing problems should disappear.

Vertical adjustment

The sagging does not allow the door to be opened for ventilation; it begins to touch the threshold when opening and closing. The situation can be corrected by adjusting the height of the hinge. Actions are performed with the loop located below:

Remove the protective cap from the loop.
Insert a screwdriver into the hole located at the top end and tighten the screw clockwise. If the door, on the contrary, needs to be lowered, the action is carried out counterclockwise. Almost always 2-3 turns is enough.

Not all PVC structures have hex-shaped holes; you may have to use an asterisk key.

Front setting

The mechanism for adjusting the pressure depends on the modification of the product:

There may be eccentrics located on the side opposite the hinges at the end of the door; they must be turned using available tools.
A number of models have a pin on the fittings. It is turned with pliers. Maximum pressure can be achieved if you give it a direction perpendicular to the door block.
In some cases it is necessary to move the strike plate. To perform this action, use the hexagon screw located under the bar.

By thoroughly cleaning the surface of the fittings and monitoring its condition, you will increase the service life of the entire PVC structure.
If the handle does not turn all the way when closing, clean, lubricate and adjust the hardware.
Opening limiters and microlifts will help reduce the frequency of adjustment.

You can learn some additional nuances of the process of adjusting plastic doors by watching the video below.

Hiring the services of a professional craftsman is not cheap, so this option should be the last resort. After reading the short instructions, you yourself can understand how to adjust the plastic balcony door. Saving money will please the family budget, and pride in the work you do yourself will strengthen self-confidence.

The balcony door needs adjustment periodically, detailed instructions later in the article

Main parts of a plastic door

Any design includes basic and auxiliary parts (see Figure No. 1). Before you start setting up, you should definitely familiarize yourself with the structure of the mechanism. It is important to correctly understand how the fittings used in the design work.

Standard composition of parts for a plastic balcony door (Figure No. 1)

The doors usually include:

PVC profiles connected by fasteners and forming a frame;
a sash made in the same way as the frame;
loops on which the canvas is held;
handle and latch used to close, open and switch to ventilation mode;
rubber seals ensuring reliable tightness;
glass unit

You should know! The list of main and auxiliary parts may change due to the presence of different functions. The main assembly is equipped with closers, stoppers, etc.

Failure Prevention

Before you start adjusting the fittings of a plastic door, you should study prevention methods that will help reduce or completely avoid the need for adjustment. They consist of correct operation and the correct selection of working parts.

At the purchasing stage, make sure that the weight of the sash is commensurate with the load that the closing mechanisms can withstand. Many types of fittings can withstand a door weight of 100-150 kg. Check out technical characteristics to make sure you make the right choice.

If the sash is open, try not to jerk it sharply. Careless handling of the system will require very frequent adjustments or repairs with replacement of parts.

Some sashes are heavy and require a sagging compensator to be installed. It looks like a specially shaped lever or roller.

Balcony door adjustment

Adjusting the plastic door various directions(Figure No. 2)

Self-adjustment of plastic door parts is based on a specific problem. There are several of them: poor sash pressure, sagging, unsteady handle, shift in seating level. Once you understand what problem you have to solve, take necessary tools: screwdrivers and hexagons.

Pressure adjustment

The clamping density should be adjusted depending on the transition to the warm or cold season. The frequency of such a procedure requires studying the instructions self-adjustment plastic doors by every owner.

Table of door clamp adjustment values (Figure No. 3)

Take a sheet of paper, place it between the sash and the frame, this way you can check the tightness of the clamp. The sheet of paper should not be pulled out after closing the window with a pen. If it moves freely, then the sash must be adjusted. First, look for locking mechanisms on the structure; they affect the clamping density. Take a key or pliers to work, rotate the locks until you achieve a sufficient degree of clamping.

The eccentrics should be adjusted if the plastic door to the balcony does not close tightly. Pick up hexagons the right size, pliers may also be required. Adjust the rear part using the screws located on the hinges. Instructions from them exact location is issued along with the fittings, but even if it is missing there should be no problems.

Adjusting the trunnions (Figure No. 4)

Adjusting the sash force (Figure No. 5)

Increasing the clamping density of the front part is carried out by rotating the trunnion (see Figure No. 4-5) in one direction, and loosening it in the other. Focus on the special serif, it is found on all types of fittings. This way you can press the door tighter in winter and looser in summer.

Adjusting the door when rubbing against the edges of the frame

If there is a shift in the landing level of the door, it begins to rub against the edges of the frame. To fix this you need to adjust the bolts in the hinges. Typically, the door is attached to three latches, which allows it to be adjusted in three directions (see Figure No. 2):

horizontally– the distance between the box and the canvas on the hinge side is set;
vertically– the height of the canvas relative to the box is adjusted;
frontally– the pressure to the sealing rubber bands is adjusted.

Open the door completely, unscrew the fasteners that secure the decorative closing strip. Then close the door and remove the decorative element from the fixing points. You must gain access to the bolt that determines the horizontal tilt. The horizontal is set by adjusting all the hinges. If the door sags, it is enough to tighten two bolts at the top and bottom so that the vertical becomes normal.

The handle is loose

The most common problem concerns the closing handle. Loosening occurs during hard use, sharp turns, or not fully tightened bolts. Also, do not hang bags or other heavy objects on the handle. In addition to becoming loose, this can cause the entire window to become skewed. The profile frame itself is not light, and additional load on it is extremely undesirable.

The photo shows how to rotate the plastic cover (Figure No. 6)

You can get to the mounting bolts by turning the plastic cap at the base of the handle a quarter turn (see Figure No. 6). Tighten the loose bolts and check their functionality. If this was not enough, there may be a crack on the part. Carefully inspect the material; if damage is found, the handle will have to be replaced.

There are times when the opposite happens - the handle moves too tightly. The problem can be solved if you lubricate the lock with a special mixture. Be careful that it does not contain acid or resin. The reason may also be incorrect positioning of the door in the opening. Adjust the position as described above.

Detailed video instructions for adjusting the balcony door

Additional information

It makes sense to adjust the door pressure only if the seal is not worn out. Otherwise, without installing a new one rubber gasket, this parameter cannot be adjusted normally.

Replacing the door seal (Figure No. 7)

Pull out the old gasket using your hands (see Figure No. 7), clean the groove from dust and other small elements. Take the new seal and install it in place. Please note that the side bend should be located on the end side of the sash. The easiest way is to remove the door and begin installation, this way you will have easy access from the hinges. It is better to buy a seal from the same company as the profiles.

We insert the seal with top side

You can increase the life of the seal using a silicone compound. Lubricate the entire surface of the rubber with it to protect it from drying out. Elastic rubber does not crack when deformed, remains intact long time.

Removing the door from its hinges

A home craftsman who maintains mechanisms on his own should know how to remove a plastic door from its hinges. This task may need to be performed in different situations. Proper removal will help avoid damage to the fittings and the door as a whole.

First, let's decide on the type of loops (click to enlarge the photo):

Design features plastic doors are not much different from entrance doors. The box is installed in the doorway, one part of the hinges is attached to it. Another part is attached to the door leaf. The number of loops is 3-4 pieces, to ensure an even load.

The distance from each other is the same. The top and bottom are set along the line of the box. By using decorative elements hide the hinges from view. This is how integrity and attractiveness are achieved appearance designs.

Reasons for dismantling

Removal is often required during renovations in a room, when replacing or adjusting a plastic balcony door. Let's take a closer look at cases in which dismantling may be required:

Need for adjustment. Some parts break and require adjustment, it is easier to do this process with removed door.
Replacing parts or blades. If a part breaks beyond repair, it must be completely replaced. In this case, you will not be able to do without dismantling. Replacing the blade will require the same steps.
Safety during repairs. Serious renovation work may pose a threat to the integrity of the door. In this case, you can cover it, but even better - remove it.
It may be necessary to remove the canvas when the dimensions of the furniture do not allow it to be brought into the room. This will help to slightly widen the available passage.

Whatever the reason, the canvas must be removed without damage and just as carefully put back in place.

Instructions for removing balcony doors

Removing the doors occurs in several stages. Let's take a closer look at each of them:

Removing decorative elements. The first step is to gain access to the hinges. Close the door without turning the handle, pry the trim with a blunt object so as not to damage the plastic, and bend it slightly.
Separating hinge elements. Press down on the top of the hinge, this will push the center pin down. Pull it out completely using pliers.
Removing the door. Take the canvas from both sides, tilt it slightly toward you and pull it up. This should disconnect the loops. It is better to carry out the procedure together, since the structure will be quite heavy.

Interesting video about how I hung the balcony door:

Conclusion

Many owners of apartments and houses have switched to using double-glazed windows, given their durability, ease of use, good performance heat preservation. Any self-respecting head of a family should understand how to regulate faulty plastic balcony doors. Such structures are used on balconies, loggias, for access to courtyard private house. Self-tuning will allow you to save money, make a timely transition to winter and summer, and avoid poor-quality service from third-party specialists. Before starting work, carefully study the manual so as not to spoil the parts. After performing the adjustment several times, you will not experience difficulties in the future.

User survey

Did you manage to solve the problem yourself using our article?