Make a drinking bowl for ducklings with your own hands. Various do-it-yourself drinking bowls for ducklings

Many farmers often prefer making their own drinking bowls, feeders and houses for their animals rather than purchasing ready-made solutions in stores. You can easily find a lot of information on this topic on the Internet and in books. We’ll talk about how to make a duck waterer with your own hands in this article.

How does a drinking bowl for a duckling differ from a drinking bowl for other birds?

Ducks tend to consume liquids much more than other birds. That is why special attention is paid to drinking bowls so that they do not become empty. The most common materials for construction are wood and iron.

Being a waterfowl species, ducklings will strive to get to the water. This means that the drinking bowl must be made in such a way that the chicks cannot get into it.

What should you consider?

The shelf should be of such depth that the ducklings can completely lower their heads into the water, especially during the hot period.
The container should not be wide, but have sufficient depth.
For ease of cleaning, the drinking bowl containers are made convenient and mobile.
The design of the drinking bowl must be fully thought out so that the water can be easily changed. It is also worth considering that ducklings should have fluid 24 hours a day.

Simple types of drinkers for ducks

A bucket, basin, bowl are very easy to use, but they have many disadvantages. The liquid gets dirty easily, so you will have to pour clean water quite often. In addition, ducklings can climb onto the basin and turn it over.

An open container can be used for young animals. Here you will need attention from the owner; the ducklings begin to push and spill water on themselves.

Wet chicks can easily catch a cold. The best solution both for the young animals and for the owner - an automatic drinker.

Nipple drinker

This option is very convenient for birds, but making such a structure with your own hands is not very easy.

Required materials:

Nipple. For older birds, the 1800 device is suitable; it starts working when moving up and down. Small duckling nipple 3600, operates 360 degrees.
A square-shaped pipe (2.2 by 2.2 cm). There should be grooves inside the block. It is important to remember that the nipples should be located at least 30-35 cm apart from each other.
Microbowl, drip eliminator.
Pipe plug.
To connect the pipes, adapters are needed.
If the drinker is not planned to be powered from a water supply system, you will need to additionally purchase hoses and a vat for water.

Unfortunately, you won’t be able to make a drinking bowl without a drill, a drill bit and a conical tap; the tools are necessary for the job.

Markings are applied to the pipe where to drill, and holes are made there that will have a diameter of 9 mm. The thread is made using a tap. The very last step is to screw in the nipples. The plug is installed on any end of the tube that is free.

As a water container best choice there will be a plastic tank. A hole is cut in the bottom of the tank, the diameter of which will correspond to the outlet hose; it can be connected immediately. The joint is wrapped with industrial tape. If necessary, those places where leakage may occur are also wrapped.

Microbowls are secured under the nipples if a 1800 nipple is used. Drop catcher (3600 nipple). The pipe is attached lengthwise to such a height that the ducklings can reach the water.

The last thing to install is the water tank. It is best to place it indoors to avoid liquid freezing in cold weather.

Homemade vacuum drinker for ducks

Making a vacuum drinker for ducks with your own hands is very simple. Most easy option- using a plastic bottle. You will need a bottle of the required volume and a tray. A frame is made from wire, with the help of which the drinker will be attached to the place designated for it.

The bottle is filled with water, the cap is screwed on, and then installed in the holder (frame). The bottom should be at the top. The tray is installed, leaving a small distance between the bottom and the neck of the bottle. To prevent water from spilling, the side of the tray should be higher than the neck. The lid unscrews and the drinker can be used.

Proper management of ducks is the key to success on the farm. Special attention devoted to feeding the livestock. This is not only a diet, but also the correct presentation. Each feeder and drinker for ducks must meet certain requirements. Choose high-quality models in the store or make them yourself.

Requirements for drinkers and feeders

Eating is an important process for the normal growth and well-being of ducks. The following requirements apply to drinkers and feeders:

Suitable size. For example, the height of the sides depends on the size of the bird.
Convenient approach for ducks and for service personnel.
Successful design. It is more convenient for ducks to drink and eat, and for humans to maintain: disassemble, wash, fill. In this sense good option- automatic models.
Reliable fastening. This preserves food, drink, and therefore saves money. Broken waterers or feeders sometimes cause injuries to ducks.
Purity. There are fewer microbes in washed dishes, which means the bird will get sick less often.
Sufficient capacity. The design is selected taking into account the size of the herd, the type of feed used, and the feeding regime.

Indian ducks and other varieties of waterfowl require a lot of water for normal life and well-being.

If possible, the herd is released to swim in a natural reservoir. Alternative option- arrange a small “pond” on the site. Even a trough will do. In winter they put it in a nesting box with a drain. Birds need to at least dip their heads. If such a container is not available, the ducks adapt drinking bowls for bathing. This is undesirable, as birds pollute and splash the water.

Advantages and disadvantages of different types of drinkers

Each product has strong and weaknesses. This is taken into account when arranging the duck house. In addition, they pay attention to the nuances of a particular farm.

Deep water container

A basin, bowl or something similar is used for the simplest drinking bowl. They use enameled, metal, plastic containers. Such products are easy to maintain and inexpensive. However, they have disadvantages:

They get clogged quickly because the container is open. Here ducks often take water treatments. This is a blow to hygiene and extra work.
For large livestock, basins and bowls are considered a poor option. It is difficult to arrange them and maintain normal sanitary condition.
More suitable for young people. It is not so convenient for adult ducks to drink from here.
They often turn over. The birds behave carelessly, push the vessels, and often try to swim there.
Dangerous low temperatures air. The water cools quickly. Plus, splashed, wet ducks freeze and get sick.
Wasteful use of water.

Another option is more suitable for thrifty owners. Vacuum drinkers provide savings. Here the required liquid level is maintained for a long time. Ducks don't splash water. There are other advantages:

The drinking bowls are closed. They are protected from various debris and contamination.
Constant supply of fresh water.
The model is easy to use and maintain.
The design can be made with your own hands.

The disadvantage of vacuum sippy cups is their low weight, which makes them easy to tip over.

Nipple (nipple) drinkers are considered by many to be the most convenient. The advantages include the following aspects:

The ducks always get clean water because the structure is closed. It's healthier for the birds and easier to maintain for people.
Water is used sparingly.
Sold at any pet store.
Suitable for indoor use in winter. In such models, the water does not cool down so quickly.
Equally convenient for both adults and juveniles.

Disadvantage nipple drinkers think complex design. Such devices are rarely made by hand, and purchased ones require money.

Grooved

Another type that is easy to make with your own hands. Although this is not the only advantage of grooved sippy cups:

long service life;
ease of maintenance;
low cost, and if you make it yourself, the device is even cheaper or free;
Many ducks quench their thirst at the same time from one trough drinker.

Not without its drawbacks:

They are heavy, making them inconvenient to carry and change water. Maintenance often requires the assistance of a second person.
If drinkers are poorly secured, ducks sometimes get injured.
Water quickly becomes polluted.
Uneconomical.

Instructions for making drinking bowls

Some farmers do without purchased structures. It doesn’t take much time to make a duck waterer with your own hands. It's simple and cheap.

Automatic drinker from a plastic bottle or canister

Many designs are very simple. For example, you can make a drinking bowl for ducklings yourself like this:

Find a suitable container made of plastic, polyethylene - a canister or bottle.
Place a container of suitable volume in the basin.
A hole with a diameter of about 1.5 cm is made at the bottom of the canister.
Close the hole with your finger.
Place it in the basin again. Ready.

The result was a simple automatic drinker. Water from a canister or bottle comes out through a hole into a tray (basin). When the birds drink water, a new portion is added automatically. Such drinkers are more suitable for adult ducks.

Grooved sewer pipe

The next design is also simple. A trough drinker is made like this:

Select a piece of sewer pipe.
They make holes in it.
Fixed on a stand.
A plug is placed at one end of the resulting workpiece.
A corner is attached on the other side. This is where the water is poured.

The fastenings must be made reliable. If the pipe falls, the ducks may be seriously injured. Sometimes the design is modified, for example, made autonomous.

Nipple (nipple)

Another type popular in large farms. A nipple drinker for ducks is made as follows:

Find square pipe. Plastic fits. From the end, the side of each “square” is a maximum of 22 mm.
A hole with a diameter of 9 mm is drilled in the pipe.
They make carvings. Use a tap for this.
Insert the nipple. The size depends on the ducks. For adults take type 1800, for juveniles - 3600.
Using the same principle, several more nipples are inserted into the pipe according to the number of wefts. The distance between the holes is 30 cm or more.
Insert a plug into the pipe on one side.
Trays are placed under all nipples for excess moisture.
Connect to a water source. You will need an adapter and a hose.

There is another simple way to make a practical drinking bowl. Vacuum structures do this:

Find a container. Sometimes they take a large jar or bottle with a volume of 50 liters. Even a three-liter jar is suitable for a small livestock. It is better to take several small containers than one large one. This way the water does not stagnate and sediment does not form in it.
Pour water into the container.
Cover with a pallet suitable size, for example, a bowl.
Press tightly.
Turn over. The bowl is at the bottom.
Installed in a duck house. Place a support under the container. To avoid injuries, they are fastened well.

What else can be used for drinking water?

There are other designs. Every farmer takes convenient materials. Someone is improving the device. Many homemade drinking bowls They are not practical, but they look original, for example:

A car tire is cut lengthwise into two parts. You get ready-made water containers. The smell is eliminated with a soda solution. Such drinking bowls are not used for large livestock, since the birds will most likely make a pool out of the drinking bowl.
They pick a large burdock and immerse it in cement mortar . Wait a few days for it to dry completely. The drinking bowl is ready. You can't call her reliable. But you can surprise visiting guests. This is a good decoration for the site.

These options can be called acceptable if the farm raises 2-3 ducks per decorative purposes.

DIY duck feeders

Dishes for food are also often made independently. As a rule, duck feeders are convenient and simple. The following varieties are popular:

Used for farms of any size. Consists of a container and a tray. A five-liter bottle and basin are suitable. Make holes and connect both parts of the structure with wire. The food pours out of an inverted bottle into a basin. When the ducks eat a portion, the next portion appears automatically.
Wooden - made of chipboard or boards. Sometimes they just take a ready-made trough. They are equipped with partitions about 20 cm wide. The height of the sides is 7–10 cm. One such duck feeder is often designed for 16–20 heads.
with a turn. The feeder is not afraid of shocks or bad weather. A plug is placed on one side of the pipe. Next, mark the places for the rectangular cutouts. The distance between them is approximately 5 cm. They drill holes and saw with a jigsaw. Securely fastened with latches.

When choosing and installing any of the models, you need to check the stability of the feeder. This will help avoid injuries among the livestock, save feed and protect it from contamination.

Installation of drinkers and feeders in the cage

Ducks are active birds. They will knock down anything that is not securely secured. Injuries and unnecessary wastage of feed or water occur. This can be avoided by following a few rules. For drinkers they are as follows:

Some types are attached to the walls of the poultry house.
Placed next to nests and feeders.
If it is a cage, hang drinking bowls with outside.
It is advisable to install water tanks indoors. This way she doesn’t freeze in cold weather. Outdoors are sometimes equipped with heaters. Those sold for aquarium fish are suitable.

Duck feeders, whether made by yourself or purchased, are also placed correctly. Sometimes they are attached to the floor. This applies, for example, to a feeder made from a sewer pipe. In other cases, they hang it on the wall. The distance is small so that the birds can get food - about 20 cm from the floor.

When purchasing or making feeders and drinkers, consider a few more points:

Containers are selected and installed so that there is water in them constantly. This is important for the proper development and health of ducks. One bird drinks approximately 270–300 liters per year. In the first days of life, ducklings need up to 0.03 liters per day. By a month this norm increases to 300 ml.
Some farmers install “dual-use” sippy cups. They are also used for bathing ducks. This is not entirely correct. Ducks need plenty of clean water to drink and a full bath. Otherwise, health problems arise - the immune system weakens, reproductive system, the sebaceous glands can't cope.
If the sippy cups are open, choose deep and narrow models. With this design, it is more convenient for ducks to immerse their heads.
They are thinking about installing more practical automatic drinkers. Particularly useful on large farms.
Some poultry keepers simply scatter feed around the pen. It's not economical. The ducks will trample most of the food. To combat losses, open feeders are filled to about a third. Additionally, protection is sometimes installed to prevent paws from climbing.
Feeders and drinkers for ducklings are made one size, for adults - another. Design features and dimensions depend on the age of the bird.

Duck waterers and feeders are chosen or done correctly. It is important to provide the livestock with not only adequate nutrition with fresh and clean food, but also constant access to water for drinking and “water procedures.”

You have quite spacious summer cottage plot or a house in the village and you decide to try to have ducks? Then this article is for you, because today we will talk about drinking bowls for ducklings and adults.

Before you buy several small yellow, fluffy lumps at the market or in a nursery, you need to prepare a comfortable pen for them with all the necessary equipment in advance.

We will share tips on how to properly arrange a place for ducks and ducklings and, in particular, how to make drinking bowls for them.

One of the most important topics The work of any poultry farmer involves the installation of drinking bowls, and this type of equipment becomes especially important when it comes to ducks, because these birds are waterfowl. That is why the production of drinking bowls for them requires special requirements. The well-being of the bird, its development and health will depend on how well the duck drinking bowl is designed.

Well, if you decide to acquire such a farm not only for yourself personally, but to a greater extent - to make a profit, then special attention should be paid to arranging drinking bowls for babies and adult ducks. In other words, good, high-quality, albeit homemade, drinking bowls for ducklings (for example, from plastic bottles) will significantly improve the living conditions of the chicks, while making it easier for the poultry farmer to care for the babies. By the way, our video below is about this.

It is important to arrange the drinkers and feeders so that they correspond to the sizes determined by the number of chicks. You should also know that the daily water requirement of an adult duck is approximately 600 ml. This indicator must be taken into account when constructing drinkers for ducks, and must be based on the calculation of how many individuals will be per container of water.

The same height of this building should be calculated according to how tall the average individual will be. Typically, this figure is about 20 cm.

To prevent the water temperature from dropping below zero during the cold season, experienced poultry farmers advise building drinking bowls with running water. When the flow of liquid is constant, it does not have time to freeze.

Types of drinking bowls for self-production

Today there are many types of bird drinkers, but some of them are quite expensive, while others cannot be “copied”, i.e. It is unlikely that you will be able to do them yourself.

Simple design for little ducklings

To make a simple drinking bowl at home, you will need an ordinary jar of no more than 2 liters in volume and some kind of saucer or plate.

We fill the jar with water, cover it on top with a saucer and, holding it, sharply turn everything upside down. Then carefully place a small stick between the saucer and the jar. Thus, water will be poured in small portions onto the saucer. A simple automatic drinker is ready.

Drinking bowl for adults

Over time, the ducklings grow up and a simple vacuum drinker is no longer enough. In addition, older individuals can easily overturn such a structure. Therefore, the farmer faces new task: make a container for grown-up ducklings that can not only provide water, but also act as a kind of washbasin, allowing the ducks to wash their beaks there.

Many novice and inexperienced poultry keepers find it easier to place a large basin in the poultry yard, in which the ducks can splash around and drink water. This should not be done under any circumstances, since ducks need fresh, clean water. And the water in which the birds bathe becomes polluted very quickly, as a result of which there is a danger of infection and pestilence of the entire population.

In order to build a simple trough drinker yourself, you need to prepare a metal sheet or a ready-made gutter in advance. You will also need a small metal grid and screws or brackets for fastening. In addition, the gutter can be cut from ordinary water pipe, carefully cutting it lengthwise and fencing it with plugs on the sides.

Then cover the finished gutter with a net and divide it in half, blocking it with any slats you have at hand.

An important point: when using such drinkers, it is advisable to install them on any, but not on metal surface so that the structure does not rattle and frighten the bird.

A good material for making a drinking bowl with your own hands can be an ordinary car tire, which needs to be cut lengthwise. Thus, you will get two full drinking bowls at once. True, first you will still have to treat the structure with some means that eliminates the pungent odor of rubber. For example, thoroughly rinse the improvised drinking bowl with water and a large amount of soda - this will get rid of the unpleasant “aroma”.

It should also be remembered that even small ducklings love and know how to swim very well, so the drinking bowl must be designed and made in such a way that the kids cannot dive into it.

Making feeders and drinkers for ducks with your own hands is a task that is feasible even for novice farmers. The advantage of such products is that you make them specifically for your case, focusing on the number of birds in your flock.

Before you figure out how to make feeders for ducks and ducklings, you should take into account several requirements in advance homemade designs. They are not complicated - basically you just need to take care of the safety of the animals, and also that the feeder or drinking bowl is easy to clean from food debris and debris.

You can make drinking bowls and feeders for ducks yourself.

Here are the basic tips you can use:

The feeder must be appropriate for the age of ducks and ducklings: ducklings at 1 month of life should have a free 5 cm for approach, and during the first year the distance is gradually increased to 12 cm. Older birds should be provided with 15 cm. The indicated parameters are given for wet food containers, while for dry ones you can take into account the dimensions 2 times smaller.
The materials used are those that are capable of preserving normal condition for a long time: they must be durable and resistant to rotting: plastic, metal sheets. Most available material- wood that can be used for dry food, and metal is well suited for wet mash.
Separately, care should be taken to ensure that drinking bowls for small ducklings are not too deep. At the same time, chicks must submerge their entire heads - this is especially important on hot days.
Finally, care must be taken to ensure that the material after processing does not have sharp edges, burrs, etc. Otherwise, the ducks and the farmer himself are at great risk of cutting themselves.

The main goal of creating your own feeders and drinkers is significant savings compared to purchased options. In addition, your own products can be adapted specifically to your case, taking into account the number of heads at each age and the location in the duck house.

Making feeders and drinkers with your own hands significantly saves your budget.

DIY duck feeders

There are feeders for dry and wet food, and if the container is made of galvanized metal sheets, it can be safely used as a universal product.

Tray feeder

A wooden tray feeder is perfect for dry food, because it can be made in literally 1 hour, and plywood and saw can be found in any household. The drawing shows an option for 10-12 adult ducks, which can approach the container from 2 sides simultaneously.

It is supposed to hang such a feeder at a height of 18-20 cm from the floor, so that it is as convenient as possible for the birds to take food.

Important. Specialized stores sell tray feeders consisting of a container and a closing part that is inserted into grooves. This is especially convenient because in this case the birds will scatter less food. In the case of homemade feeder you can make a similar cover, or you can slightly increase the height of the sides and mount them at a slight angle.

If you make a trough feeder from a metal sheet, it will work well for wet mash.

A tray or groove feeder is suitable for mash.

Hopper feeder

A bunker feeder is a common version of an automatic feeder for dry mixtures, which is especially convenient because you can put a lot of food into it at once for several days.

Along with wood, a galvanized sheet is also suitable, on which you need to make the appropriate markings with a marker, bend it in the right places, and fasten it, like a wooden bunker, with self-tapping screws.

The simplest automatic feeder for ducklings

If you need to quickly build an additional feeder because the old one is broken and the ducklings do not have enough feeding points, this model will literally help out. You will need a 5-liter canister, wire and a bowl into which dry food will be poured. Along the diameter of this basin, in 8 places you need to make holes for the wire (it is better to take the thickest one you can find).

We make holes in the bottle in exactly the same places. We insert pieces of pre-cut wire into the holes of the basin and container, bending the edges so that the structure is firmly supported by weight - the food should flow freely from the bottom neck of the bottle (we fix it upside down).

A feeder for ducklings can be made from a 5 liter bottle.

Simple DIY duck drinkers

You can build a drinking bowl in a matter of seconds, and there is no need to monitor the device - all designs provide for the automatic supply of new portions of water as the birds consume it due to gravity.

Drinkers made from plastic bottles

Very simple options Drinkers for ducks and ducklings can be made from plastic bottles of different sizes:

Automatic drinker from a large bottle (5-6 liters)- This good decision for adult ducks: a bottle (canister) of the specified volume is placed in a regular basin, in the lower quarter of which a hole with a diameter of 1.5 cm is made (the finger should completely block it). When pouring water into the bottle, close the hole, then place the full canister in the basin and remove your finger: the water is poured into the container, and when the animals consume it, additional portions will fill the basin themselves.
For ducklings, a design made of a glass or plastic jar with a volume of 1.5-2 liters and a saucer is suitable. Pour water into the container, cover the top with a saucer and press it tightly against the jar. We sharply turn the structure upside down so that the saucer is at the bottom. We install it in a room with ducklings and carefully place a small wooden stick under the jar so that water begins to leak into the saucer.

For small ducklings a simple one is suitable vacuum drinker from a can and a plastic stand.

Nipple drinker for ducklings

This drinker is intended mainly for ducklings. It is also called the teat because the chicks receive water in the same way that calves and other animals drink milk from their mother’s breast.

You will need the following tools and items:

square pipe - you can take a small plastic pipe with square side dimensions within 22 mm;
nipples are selected depending on what birds you are going to feed: for small chicks you need to choose type 3600, which turns in different directions, and for older birds you can choose type 1800, which work on the “up-down” principle;
plug for square pipe;
a large container of water and a rubber tube - a source of water supply (or a central source);
an adapter that connects a square pipe to a rubber round one.

The tools you will need are an electric drill (9 mm drill) and conical tap for carving.

The sequence of actions is as follows:

Trough drinker for adult ducks

It is best to make a drinking bowl for ducks and any other birds from materials that are resistant to rotting and quite durable.

In this sense plastic pipe large diameter fits perfectly:

it is inexpensive;
easy to install;
will last a very long time;
Due to its length, it is capable of providing water to a large flock of several dozen ducks;
cleaning it from dirt is also quite simple - if you do this regularly, then no deposits will form on the surface of the plastic;
Finally, this drinking bowl essentially combines the function of a small washbasin - ducks will be able to wash their beaks and cool down in hot weather by plunging their heads into the water.

The instructions for its manufacture are obvious - you need to cut several identical holes (for ducklings - small, for adult ducks - 3-4 times larger in all dimensions) and install it on a pre-designed durable stand. One end of the pipe is screwed with a plug, and an angle is installed on the other, through which water is poured.

The simplest drinker for ducks - sewer pipe with holes.

Important. Such a drinking bowl must be installed very securely, because if the pipe falls on the birds, they will inevitably receive severe damage, and large quantities of water will spill throughout the duckling.

The only drawback of such a device is that, together with water, it is quite heavy, and ducks will caress their beaks quite often, so the water will also have to be changed often. You will need the help of a second person to pull out the pipe, holding it on both sides.

Unusual drinking bowl

And finally - original idea on creating a drinking bowl from a large leaf of burdock or other plants.

First, it is immersed in a cement solution so that it retains its concave shape. You need to wait 2-3 days until the mixture hardens, and then paint it to your liking and dry it thoroughly in the sun.

This is a summer drinker, which, of course, serves aesthetic purposes, not practical functions. However, if you wish, you can decorate your area with similar items.

Here are tips from farmers who have been breeding ducks for several years and therefore have relevant experience self-made feeders and drinkers for ducks and other poultry.

Farmers do not recommend making feeders from thin plastic.

Yuri. At first, when I started working with ducks and poultry in general, I bought plastic feeders. However, they did not withstand either the test of frost or the test of time. Therefore, in general, I recommend either paying attention to a specific manufacturer of the product, or making it yourself. In addition, making both a feeder and a water bowl for any number of ducks is very simple even for those who are encountering this for the first time. For example, buying a sewer pipe and cutting out several holes, installing plugs and making supports is a simple task. But it turns out to be a drinking bowl for a whole flock. Yes, and it’s quite suitable for feed, you just need to make the holes correspondingly larger. In this regard, the line between a drinker and a feeder is small - essentially the same structures, only with different materials.

Nikolai. Making feeders yourself is a good skill that will be useful on the farm. My favorites are automatic feeders and automatic waterers. For example, the same option with a hopper feeder made of metal sheet is a very simple product. You fold it like a paper boat - just make all the markings clearly, because even small errors make the structure leaky.

Anatoly. I draw the attention of beginners to important nuance any feeder or drinker: making it is one thing, but attaching it securely is another. A neighbor had an incident when big pipe filled with water and killed several ducks, which had to be slaughtered immediately. Keep this in mind - ducks are quite active birds, if anyone has ever raised them. And when there are a lot of them, they can easily turn over anything. Therefore, you need to literally fasten it tightly. Ducklings are another matter - you can simply hang them, but again securely, so as not to take risks.

Drinkers and feeders for ducks and other poultry can be purchased at appropriate stores. However, making them yourself is great solution get rid of unnecessary things in the household. In addition, this option is well suited for those farmers who are located far from large stores, and there is no need to travel to larger settlements in the near future.

In the video, a farmer explains how to properly make water bowls and feeders for ducks.

Every breeder thinks about how to save money, so he often arranges the poultry house on his own. Many of them decide to do DIY drinking bowls for ducklings because they want to create optimal conditions for individuals. For this purpose, they build a place to keep ducklings and arrange the appropriate equipment.

As for drinking bowls, they must correspond directly to the size of the number of ducklings. Wood, glass or metal are perfect for making your own drinking bowl.

Features of drinkers for small ducklings

The average length of the structure itself should be on average about 20 cm. The thickness of the walls is 3 cm. When making drinking bowls for babies with your own hands, the breeder should take into account the following aspects:

The drinking bowl should be deep enough for individuals to dip their heads, this is especially important during periods of extreme heat.
Compact design – important factor, because the more ergonomic the drinker, the easier it will be to clean.
Thoughtful design with clean water, which corresponds to the age and number of ducklings.

A large automatic waterer for ducklings, which is very easy to make yourself

Often, such drinking bowls at home are made from scrap materials, including basins, plastic bowls, enamel buckets or other available means. However optimal option for “refreshing” - this is the manufacture of an automatic drinker.

How to build a drinking bowl for ducklings with your own hands?

Simple tips and recommendations from farmers will certainly make the task easier for novice breeders. There are many manufacturing options, but let's consider the simplest and most budget method. Stages of making a drinking bowl for ducklings in household from scrap materials:

Take a regular one glass jar, the volume of which is 1.5-2 liters, as well as a plate or saucer.
Then this container must be covered with a plate and turned over sharply. A stick or tube should be placed between the jar and the plate, so that the liquid will gradually and slowly pour out as it decreases.
When there is no more water in the drinking bowl, you should turn the structure back 180 degrees.

Simple drinker for ducklings