There are many types of light-protective sheets, but they have common features. All of them consist of a metal tube-roller, or rod, on which fabric is wound: bamboo or cotton material. The length is adjusted using a chain that is attached to a rotating mechanism on one side of the roll.
Usually at the bottom of the curtain there is a steel or wooden weight bar that protects it from deformation, allows it to hang evenly and fit tightly to the glass. The latter is achieved using a pair of small magnets that are glued to the bottom of the frame and attract the weighting material, if it is metal.
You can take a more complicated route and thread a fishing line through the guides, which will hold the roller shutter during wind fluctuations and opening in the “window” mode. It must first be threaded into the upper fasteners several times so that when tensioned it does not pull out. Unwind it all the way and insert it into the special eyelet on the weight bar. At the bottom of the frame, attach small corners with holes for fishing line. Pull it there, tie it, cut off the excess.
Sometimes manufacturers install a spring inside the shaft. In this case, there is no need to fiddle with the cord with your hands to open or close it. It is enough to pull the plumb line located on the bottom bar with a little effort.
Installation sequence:
- We outline the locations of the fasteners.
- We drill holes, put the side clamps in place, and secure them with self-tapping screws.
- We put the roller with the cloth in place and close the plugs.
- We prepare the guides for installation, remove the protective tape from the self-adhesive layer. Lower the curtain by 20-25 cm.
- We place the canvas under the guides and carefully glue them in place.
- We install limiters on chain mechanism or a decorative weight for a weight bar. We check the functionality.
Installation of cassette models
- First apply the markings.
- Using a level, adjust the “horizon” of the location of the roller shutter.
- Drill holes at the marked points.
- Using self-tapping screws at the top of the glass unit, screw the box with the roll rolled up inside it.
- If you don't want to make holes, use tape at least a millimeter thick. But first, work some magic on the markings so that the box hangs evenly.
Roller shutters - good decision for any interiors. They are practical, beautiful and allow you to effectively regulate the level of illumination in the room. Night/day roller blinds are especially good for this. For those who do not want to give up traditional curtains, we can recommend using them in combination with rolls. The result is very interesting and functional combinations.
- Material prepared by: Natalya Utochkina
Which are also sometimes called mini, is a simple design consisting of two guide bars, a fishing line for twisting the fabric, and the curtain itself. All this is complemented by fasteners. These curtains look very beautiful! But in addition to the fact that they need to be assembled, they also need to be installed, and they also need to be properly cared for.
What does the assembly include? roller blinds?
In chronological order:
- Careful unpacking (it is better to use a plastic knife, which cannot damage either the canvas itself or the rolling mechanism).
- Preparing the back bar with magnets, which will act as a limiter (the magnet itself holds the bar in the lower position and prevents the canvas from sagging).
- Primary installation of the fastening (if you plan to install it on complete brackets).
- It is recommended to iron the fabric itself at a low temperature before installation - this is not prohibited and will not harm the fabric in any way.
- It is recommended to assemble roller blinds with fasteners and prepare the profile for installation of all elements. If we are talking specifically about a plastic window (and it is for them that mini-blind systems are produced), then it will either have to be drilled (for self-tapping screws) or all metal components should be placed on adhesive double-sided tape.
Roller blinds: fastening installation
The first step is to install the fasteners. It consists of three parts - upper hinges, lower hinges and brackets that will hold lifting mechanism. Some kits provide special plastic or wooden plugs that will visually cover the fasteners.
The easiest way to install is with adhesive tape. Its advantage is that you don’t have to damage the profile itself. Suitable for most simple models windows in which the installation of additional guides is not provided. Just keep in mind that this procedure is not performed using conventional double sided tape, but using construction adhesive tape with a soft (foam rubber) base, which must be ironed (or heated with a hot air gun) before use.
Before hanging the fasteners in place, it is necessary to take the correct measurement.
What to consider when measuring
- The canvas does not necessarily need to be opened completely. The mini system looks more attractive if the indentation at the top and bottom of the profile is the same.
- Under no circumstances should you melt a PVC profile. If you plan to glue the tape, then degrease the installation areas with regular alcohol, but not with acetone or other solvents.
- The markings with guides should be based on the geometry of the window opening. It shouldn’t happen that on one side the indentation will be smaller or larger. At the top you need to leave enough space to fully open the sash (about 3-4 centimeters higher above the profile).
If you plan to mount the brackets on a rigid connection with the profile and will need to drill the PVC base, then for these purposes would be better suited Dremel with the drill rotation speed set to the lowest speed (in no case the one used for metal or for figure cutting glass).
First you need to install the lower rear bar and adjust according to it the desired height roller blinds. As a rule, manufacturers do not knit a fishing line for this in the kit - you will need to do this yourself during the installation of the rolling mechanism.
The brackets are attached with 2-4 self-tapping screws (depending on the manufacturer). This is where the instructions will help, indicating exactly how the fasteners should be positioned for proper installation and pulling of the fishing line and canvas. As a rule, the “ears” converge at inner side profile, which allows them to be hidden from prying eyes with decorative plugs.
Before the canvas is secured with strings, you need to calculate the diameter of the shaft with the curtains wound on it. The standard diameter of the mechanism is 19 millimeters for the base, and another 4-6 for the curtains themselves. But there are systems where the shaft is 25 millimeters, and even 32. The latter are full-fledged wide beams that are used to attach a roll system to a doorway or a huge window with a wide profile.
Assembling the lifting mechanism is quite simple. The shaft itself is already assembled with springs.
The buyer should only:
- Pull the fishing line over the edge of the curtain (if necessary, shorten the fabric, creating a wider fold);
- Tie the fishing line at both ends (in a loop);
- Thread the loops through the shaft brackets.
Lastly, a sinker is attached to the bottom of the curtain (a plastic or aluminum weight with iron inserts that will rest against the magnet on the bottom rear bar). As a rule, almost all mini systems provide mounting guides until they click (the only drawback is that this is done plastic inserts, which wear out over time).
After the curtain and lifting mechanism are installed in their grooves, their operation should be thoroughly tested. This is necessary in order to make sure that the fishing line is not compressed anywhere, is not tied into a knot or jammed.
Some manufacturers additionally add silicone oil to the kit - it is used to lubricate the grooves into which the wrapping shaft is installed. This operation needs to be performed only 1-2 times a year. You can replace silicone oil with the one used for lubrication. sewing machines(sold in a textile store).
Proper care of roller blinds
Caring for roller blinds includes:
- Maintenance of the shaft on which the curtains are wound (lubrication of its side parts);
- Washing the fabric itself (performed 1-2 times a year, and be sure to read the instructions);
- Removing dirt from the back strips and fasteners (for this, use a soap solution or window cleaning liquid).
If we are talking about roller blinds like blinds (combined lifting mechanism), then caring for them also includes washing the slats themselves (if they are collapsible). Cleaning from dirt is also carried out with a soap solution without aggressive household chemicals.
It should be noted that if the windows are planned to be switched to thermal insulation mode for the winter, then before performing this operation it is recommended to dismantle the canvas and the lifting mechanism of the roller blinds. After clamping the grooves plastic profile– they can be put back.
Attention, TODAY only!
Professionals know what it is roller blinds how to assemble and install them. If these processes are carried out with your own hands, you will need to find out the principle of the curtains.
Roller blinds can be attached to the window in two ways: with double-sided tape or with self-tapping screws to the bracket.
Sequencing
Roller blinds consist of a bracket, a control mechanism, a control chain limiter, a bracket area for fixing curtains, and grips. Some products come with additional system fixing curtains used for opening windows. First assemble the bracket. To do this, you will need to fix its constituent elements.
Assembly diagram for roller blinds bracket.
Double-sided tape is glued to the bracket. If installation work are made using self-tapping screws, then a platform is not required. The brackets are connected to the platforms until they click. To fix the parameters of the product, the structure is assembled on the windowsill. Then it is applied to the window sash. Use a pencil to mark the location of the right and left pads. The next step involves the final gluing of the platform to the sash.
Before carrying out this procedure, the surface is degreased. To do this, use alcohol or gasoline for lighters. Double sided tape Can only be glued once. If the right bracket is fixed, put the shaft on it. The fabric is wound on the last unit. The left bracket is attached to the structure. Make a mark of the location of the corresponding site. The left bracket is disconnected from the platform. The last element is glued to the window profile taking into account the marks made.
The shaft is inserted into the right bracket. The left analogue is fixed. The curtain comes down. The location of the magnetic clamp will need to be marked with a pencil. The curtain is attached to the sash taking into account the width of the fabric. If necessary, a specialist can take measurements.
Return to contents
Assembly process without box
Roller blinds various systems, including Mini, are delivered unassembled without a box. The assembly of such a system begins with cutting the packaging and studying the instructions. The fishing line is threaded through the holes provided in the corners. Double knots are made at the ends of the fishing line. The line is cut in half. The capsules are inserted into the curtain shaft and snapped into the corners.
Subsequent assembly is carried out simultaneously with the installation of the entire structure. There are several methods for attaching the product in question.
If roller blinds are installed on the sash of a window opening, there is minimal loss of usable space.
Initially, you will need to measure the product.
Roller blinds are presented in the form of a simple design. The fabric is wound onto a shaft. The device has a special mechanism for lowering and raising curtains without a box. If such products are made to order, then the canvas does not need to be adjusted. Otherwise, the curtains are cut.
To do this you will need to take measurements. The length of the rolled web is understood as the distance between the outer edges of the horizontal glazing beads; the width is the distance between the corresponding vertical elements. The canvas is unrolled and removed from the shaft. A plug with a projection is mounted on the shaft.
Roller blinds are laid out on a flat surface. The required width is measured on the product and a mark is made. Curtains can be cut using scissors or a construction knife. The next step involves fixing them to the shaft. First you will need to remove the protective film from the surface of the last element. The upper edge of the product is bent upward by 5 cm. The shaft is placed in a niche with the strip facing up. The 1st element is installed in a horizontal position.
Roller blinds are a very popular and stylish interior detail that looks impressive in any room. Today this is one of the most relevant and popular methods of installing plastic windows.
Such curtains are easy to install, practical, do not require complex care and when choosing quality materials and proper fasteners will serve you for many years.
In this article we will tell you how to install roller blinds on plastic windows with our own hands, and we will also clearly demonstrate this process on video. We hope that here you will find answers to all your questions and get a lot of useful tips that will help you in your work.
Traditional types
Attaching roller blinds to plastic windows can be done in many different ways. Today there are such a large number of them that it is not possible to talk in detail about each of these varieties. Let us give as an example the two most popular types of fastening, each of which, if you have certain knowledge and skills, you can easily implement with your own hands:
- The most familiar and traditional way lies in the fact that the fastening is made to the window opening. In this case, the canvas is fixed either on the surface of the wall or on the ceiling, and freely falls along the plastic window. This method is very popular, however, it is associated with certain risks. In order to attach roller blinds to the ceiling or wall, you will have to drill several holes into which you will insert profiles for fastening. If you choose this method and want to do the installation yourself, you will have to be extremely careful and attentive to avoid mistakes and unwanted damage (you can watch the process of carrying out such work by watching the video provided).
- The second common fastening method is very similar in its basic principle to the previous one. The only difference is that the canvas is not fixed on the wall or ceiling, but directly on the window. It is usually attached to the frame. The type of fastener used is the same. Several holes are drilled into the surface of the frame, into which special fasteners are subsequently inserted. Choosing this method, you must also be extremely careful, because when drilling you risk damaging the surface of the window and ruining it. If you are not confident in your abilities, it is better to seek the help of specialists who will cope with this work efficiently and professionally.
Both of these methods are very relevant today and are used everywhere. They have a lot of advantages, but their main disadvantage can be considered insufficient practicality. To hang roller blinds on the windows, you will have to break the integrity of either the wall, the ceiling, or the frame. This is fraught with undesirable consequences. Any careless movement can lead to an error that can no longer be corrected. This is especially dangerous if you have just purchased new expensive windows that are under warranty.
However, this installation method also has a lot of advantages. The main ones are strength and reliability. You can be sure that such curtains will be fixed very firmly. Thanks to this excellent quality, both of these methods are so relevant and in demand today.
Installation without drilling
If you want to install roller blinds without risk, we advise you to use the installation method without drilling. This method is the safest, unlike the options described above. In addition, it is very simple and accessible, so almost anyone can cope with such work, and it will not require a long time.
Installation without drilling is carried out using special construction adhesive or tape. Today, dozens of such materials are available for free sale, which differ in their cost and characteristic features. We advise you to refuse to buy cheap formulations and choose a higher quality and reliable option, which will provide you with a strong and durable hold.
When choosing between tape and glue, rely on your personal preferences. As practice shows, both of these materials (provided that you choose a proven and good composition) can be very practical and have excellent adhesive abilities. Buy special options that are designed to fix such structures without drilling.
Installation in in this case can be carried out both on the surface of the wall or ceiling, and directly on the frame. The choice of one method or another depends solely on your decision, as well as on the layout features and design mechanism. In any case, fixing the canvas without drilling using professional construction adhesive or double-sided tape seems to be the simplest, safest and fastest way.
